Set-ResourceConfig

Reference

Module:: ExchangePowerShell

Applies to:: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

This cmdlet is available in on-premises Exchange and in the cloud-based service. Some parameters and settings may be exclusive to one environment or the other.

Use the Set-ResourceConfig cmdlet to create custom resource properties that you can add to room and equipment mailboxes.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Set-ResourceConfig
   [-Confirm]
   [-DomainController <Fqdn>]
   [-ResourcePropertySchema <MultiValuedProperty>]
   [-WhatIf]
   [<CommonParameters>]

Description

After you use this cmdlet to create custom resource properties, you use the ResourceCustom parameter on the Set-Mailbox cmdlet to add one or more of those properties to a room or equipment mailbox. For more information, see the ResourceCustom parameter description in Set-Mailbox.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Set-ResourceConfig -ResourcePropertySchema Room/Whiteboard,Equipment/Van

This example adds the custom resource properties Room/Whiteboard and Equipment/Van. These values replace any existing custom resource properties that are already configured.

Example 2

Set-ResourceConfig -ResourcePropertySchema @{Add="Room/TV"; Remove="Equipment/Laptop"}

This example adds the custom resource property Room/TV and removes Equipment/Laptop without affecting other custom resource properties that are already configured.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

Type:	SwitchParameter
Aliases:	cf
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-DomainController

This parameter is available only in on-premises Exchange.

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:	Fqdn
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019

-ResourcePropertySchema

The ResourcePropertySchema parameter specifies the custom resource property that you want to make available to room or equipment mailboxes. This parameter uses the syntax Room/<Text> or Equipment/<Text> where the <Text> value doesn't contain spaces. For example, Room/Whiteboard or Equipment/Van. You can specify multiple values separated by commas.

To enter multiple values and overwrite any existing entries, use the following syntax: Value1,Value2,...ValueN. If the values contain spaces or otherwise require quotation marks, use the following syntax: "Value1","Value2",..."ValueN".

To add or remove one or more values without affecting any existing entries, use the following syntax: @{Add="Value1","Value2"...; Remove="Value3","Value4"...}.

Type:	MultiValuedProperty
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:	SwitchParameter
Aliases:	wi
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019, Exchange Online

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.

Dela via