Поделиться через


Troubleshooting Enabling Multisite

 

Applies To: Windows Server 2012 R2, Windows Server 2012

This topic contains troubleshooting information for issues related to the Enable-DAMultisite command. To confirm that the error you received is related to enabling multisite, check in the Windows Event log for the event ID 10051.

User connectivity issues

Users may experience connectivity issues when you enable multisite if the configuration is not correct.

Cause

In a multisite deployment, Windows 8 client computers are able to roam between different entry points. Windows 7 client computers must be associated with a specific entry point in the multisite deployment. If client computers are not in the correct security group, they may receive the wrong group policy settings.

Solution

DirectAccess requires at least one security group for all Windows 8 client computers; we recommend using one security group for all Windows 8 computers per domain. DirectAccess also requires a security group for Windows 7 client computers for each entry point. Each client computer should be included in only one security group. Therefore, you should make sure that the security groups for Windows 8 clients contain only computers running Windows 8, and that each Windows 7 client computer belongs to a single dedicated security group for the relevant entry point and that no Windows 8 clients belong to the Windows 7 security groups.

Configure the Windows 8 security groups on the Select Groups page of the DirectAccess Client Setup wizard. Configure Windows 7 security groups on the Client Support page of the Enable Multisite Deployment wizard, or on the Client Support page of the Add an Entry Point wizard.

Kerberos proxy authentication

Error received—Kerberos proxy authentication is not supported in a multisite deployment. You must enable the use of computer certificates for IPsec user authentication.

Cause

Computer certificate authentication must be enabled before enabling multisite.

Solution

To enable computer certificate authentication:

  1. In the Remote Access Management console, in the details pane, under Step 2 Remote Access Server, click Edit.

  2. In the Remote Access Server Setup wizard, on the Authentication page, select the Use computer certificates check box, and select the root or intermediate certification authority that issues certificates in your deployment.

To enable computer certificate authentication using Windows PowerShell, use the Set-DAServer cmdlet and specify the IPsecRootCertificate parameter.

IP-HTTPS certificates

Error received—The DirectAccess server uses a self-signed IP-HTTPS certificate. Configure IP-HTTPS to use a signed certificate from a known CA.

Cause

The IP-HTTPS certificate is self-signed. You cannot use self-signed certificates in a multisite deployment.

Solution

To select an IP-HTTPS certificate:

  1. In the Remote Access Management console, in the details pane, under Step 2 Remote Access Server, click Edit.

  2. In the Remote Access Server Setup wizard, on the Network Adapters page, under Select the certificate used to authenticate IP-HTTPS connections, make sure the Use a self-signed certificate created automatically by DirectAccess check box is cleared, and click Browse to select a certificate issued by a trusted CA.

Network location server

  • Issue 1

    Error received—DirectAccess is configured to use a self-signed certificate for the network location server. Configure the network location server to use a signed certificate from a CA.

    Cause

    The network location server is deployed on the Remote Access server and uses a self-signed certificate. You cannot use self-signed certificates in a multisite deployment.

    Solution

    To select a network location server certificate:

    1. In the Remote Access Management console, in the details pane, under Step 3 Infrastructure Servers, click Edit.

    2. In the Infrastructure Server Setup wizard, on the Network Location Server page, under The network location server is deployed on the Remote Access server, make sure the Use a self-signed certificate check box is cleared, and click Browse to select a certificate issued by an Enterprise CA.

  • Issue 2

    Error received—To deploy a network load balanced cluster or multisite deployment, obtain a certificate for the network location server with a subject name that is different from the internal name of the Remote Access server.

    Cause

    The subject name of the certificate used for the network location server website is the same as the internal name of the Remote Access server. This will cause name resolution issues.

    Solution

    Obtain a certificate with a subject name that is not the same as the internal name of the Remote Access server.

    To configure the network location server:

    1. In the Remote Access Management console, in the details pane, under Step 3 Infrastructure Servers, click Edit.

    2. In the Infrastructure Server Setup wizard, on the Network Location Server page, under The network location server is deployed on the Remote Access server, click Browse to select the certificate you previously obtained. The certificate must have a subject name that is different from the internal name of the Remote Access server.

Windows 7 client computers

Warning received—When enabling multisite, the security groups configured for DirectAccess clients must not contain Windows 7 computers. To support Windows 7 client computers in a multisite deployment, select a security group containing the clients for each entry point.

Cause

In the existing DirectAccess deployment, Windows 7 client support was enabled.

Solution

DirectAccess requires at least one security group for all Windows 8 client computers and a security group for Windows 7 client computers for each entry point. Each client computer should be included in only one security group. Therefore, you should make sure that the security group for Windows 8 clients contains only computers running Windows 8, and that each Windows 7 client computer belongs to a single dedicated security group for the relevant entry point and that no Windows 8 clients belong to the Windows 7 security groups.

Active Directory site

Error received—The server <server_name> is not associated with an Active Directory Site.

Cause

DirectAccess could not determine the Active Directory site. In the Active Directory Sites and Services console you can configure the different subnets for your network and associate each subnet with the relevant Active Directory site. This error may occur if the IP address of the Remote Access server does not belong to any of the subnets, or that the subnet to which the IP address belongs is not defined with an Active Directory site.

Solution

Confirm that this is the issue by running the command nltest /dsgetsite on your Remote Access server. If this is the issue, the command will return ERROR_NO_SITENAME. To solve this issue, on your domain controller, make sure that a subnet which contains the internal server IP address exists and that it is defined with an Active Directory site.

Saving server GPO settings

Error received—An error occurred while saving Remote Access settings to GPO <GPO_name>.

Cause

Changes to the server GPO couldn’t be saved either due to connectivity issues or if there is a sharing violation on the registry.pol file, for example, another user has locked the file.

Solution

Make sure that there is connectivity between the Remote Access server and the domain controller. If there is connectivity, check on the domain controller if the registry.pol file is locked to another user, and if necessary, end that user session to unlock the file.

Internal error occurred

Error received—An internal error occurred.

Cause

This may be caused by an unexpected entry point table configuration in the client GPO. This can occur if the administrator uses DirectAccess client cmdlets to edit the entry point table in the client GPO.

Solution

Review the entry point table configuration in all client GPOs and fix any inconsistencies in the multisite configuration between the different instances of the client GPOs and the DirectAccess configuration. Use the Get-DaEntryPointTableItem cmdlet with the name of the client GPO to get the entry point table on the client. Use the Get-NetIPHttpsConfiguration cmdlet to get all the IP-HTTPS profiles for all the entry points.

For further information, see DirectAccess Client Cmdlets in Windows PowerShell.