CMPLANNER Configuration Service Provider

4/8/2010

The CMPLANNER Configuration Service Provider configures the preferred connections for each network. These preferred connections are used by the Connection Manager. This Configuration Service Provider can also set the settings for those connections.

Note

This Configuration Service Provider is a proprietary extension of the OMA DM protocol, and must be used when provisioning devices using OMA DM. To provision devices using the OMA Client Provisioning (formerly WAP Client Provisioning) protocol, use the CM_Planner Configuration Service Provider instead. Access to this Configuration Service Provider is determined by Security roles. Because OEMs and Mobile Operators can selectively disallow access, ask them about the availability of this Configuration Service Provider. For more information about roles, see Security Roles and Default Roles for Configuration Service Providers.

The following image shows the management object used by OMA DM.

• CMPLANNER
  The root node for CMPLANNER object. The following table shows the default settings.

  Data Type	Node
  Roles allowed to query and update setting	Manager AuthenticatedUser
  Access Type	Read/Write
  Occurs	Once

• CMPLANNER/CacheTime
  Specifies the default time, in seconds, for which the planner will cache released connections. The following table shows the possible values.

  Value	Description
  0	None
  30	30 seconds
  60	1 minute
  300	5 minutes
  600	10 minutes

  The following table shows the default settings.

  Data Type	Integer
  Label	Idle disconnect after:
  Roles allowed to query and update setting	Manager AuthenticatedUser

  The Connection Manager does not cache the following types of connections:

  • Suspended connections
  • Disconnected connections
  • Connections without a DestId (that is, when the connection was provisioned using provisioning XML, a DestId was not specified)
  • Fixed path connections (that is, a connection where the destination GUID is set to be an existing network connection managed using the Connection Manager)

  **.

• CMPLANNER/CoeffBandwidth
  Specifies a bandwidth coefficient, in 16.16 fixed point, for planner path calculations. The default value is 0x10000, which corresponds to 1.0.

  The following table shows the default settings.

  Data Type	Integer
  Label	Bandwidth Coefficient
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/CoeffCost
  Specifies a cost coefficient, in 16.16 fixed point, for planner path calculations. The default value is 0x10000, which corresponds to 1.0.

  The following table shows the default settings.

  Data Type	Integer
  Label	Cost Coefficient
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/CoeffLatency
  Specifies a latency coefficient, in 16.16 fixed point, for planner path calculations. The default value is 0x10000, which corresponds to 1.0.

  The following table shows the default settings.

  Data Type	Integer
  Label	Latency Coefficient
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/FailoverDefault
  Sets the default value for the yes/no buttons of the failover prompt. Permitted values are 0 (no) or 1 (yes).

  Note

  The prompt has an internal timeout, so this also controls the default action if the user does not respond to the prompt within the time limit. If the failover prompt is disabled, this parameter also specifies whether failover is allowed.

  The following table shows the default settings.

  Data Type	Boolean
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/FailoverPrompt
  Specifies whether the planner displays a yes/no prompt before using a non-preferred connection, for example if the preferred connection is unavailable. The following table shows the possible values.

  Value	Description
  0	Do not display a prompt
  1	Display a prompt

  The following table shows the default settings.

  Data Type	Boolean
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/RetryCount
  Specifies the number of times the planner retries failed connection attempts. Possible values for this parameter are 0, 1, 2, 3, 4 and 5. A value of 0 causes the planner to fail the connection attempt after the first try. A value of 1 causes the planner to retry the connection once.

  The following table shows the default settings.

  Data Type	Integer
  Label	Redial attempts:
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/PreferredConnections
  Specifies the preferred connection to use when connecting to a specific destination network.

  The following table shows the default settings.

  Data Type	Node
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/PreferredConnections/Internet
  Specifies the preferred connection to use when connecting to the Internet. The value must be the entry name of a connection, which may be the initial node on a path connecting the device to the specified destination network.

  The following table shows the default settings.

  Data Type	String
  Label	Internet connection:
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/PreferredConnections/Work
  Specifies the preferred connection to use when connecting to the Work metanetwork. The value must be the entry name of a connection, which may be the initial node on a path connecting the device to the specified destination network.

  The following table shows the default settings.

  Data Type	String
  Label	Work connection:
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/PreferredConnections/WAP
  Specifies the preferred connection to use when connecting to a WAP network. The value must be the entry name of a connection, which may be the initial node on a path connecting the device to the specified destination network.

  The following table shows the default settings.

  Data Type	String
  Label	WAP connection:
  Roles allowed to query and update setting	Manager AuthenticatedUser

• CMPLANNER/PreferredConnections/SecureWAP
  Specifies the preferred connection to use when connecting to a WAP network. The value must be the entry name of a connection, which may be the initial node on a path connecting the device to the specified destination network.

  The following table shows the default settings.

  Data Type	String
  Label	Secure WAP connection:
  Roles allowed to query and update setting	Manager AuthenticatedUser

See Also

Reference

CM_Planner Configuration Service Provider

Concepts

Configuration Service Provider Reference for Windows Mobile Devices
CMPLANNER Configuration Service Provider Example for OMA DM