MmAllocateContiguousMemorySpecifyCacheNode function (wdm.h)
The MmAllocateContiguousMemorySpecifyCacheNode routine allocates a range of contiguous, nonpaged physical memory and maps it to the system address space.
Syntax
PVOID MmAllocateContiguousMemorySpecifyCacheNode(
[in] SIZE_T NumberOfBytes,
[in] PHYSICAL_ADDRESS LowestAcceptableAddress,
[in] PHYSICAL_ADDRESS HighestAcceptableAddress,
[in, optional] PHYSICAL_ADDRESS BoundaryAddressMultiple,
[in] MEMORY_CACHING_TYPE CacheType,
[in] NODE_REQUIREMENT PreferredNode
);
Parameters
[in] NumberOfBytes
The size, in bytes, of the block of contiguous memory to allocate. For more information, see the Remarks section below.
[in] LowestAcceptableAddress
The lowest valid physical address the caller can use. For example, if a device can address only locations above the first 8 megabytes of the processor's physical memory address range, the driver for this device should set LowestAcceptableAddress to 0x0000000000800000.
[in] HighestAcceptableAddress
The highest valid physical address the caller can use. For example, if a device can address only locations in the first 16 megabytes of the processor's physical memory address range, the driver for this device should set HighestAcceptableAddress to 0x0000000000FFFFFF.
[in, optional] BoundaryAddressMultiple
The physical address multiple that the allocated buffer must not cross. A physical address multiple must always be a power of two. This parameter is optional and can be specified as zero to indicate that the device has no special memory boundary restrictions. For more information, see Remarks.
[in] CacheType
Specifies a MEMORY_CACHING_TYPE value, which indicates the type of caching requested for the contiguous physical memory.
[in] PreferredNode
The preferred node number. If a multiprocessor system contains N nodes, the nodes are numbered 0 to N-1. If MM_ANY_NODE_OK is specified or the machine only has one node, then the allocation is satisfied from any node. Otherwise, the allocation is made from the preferred node or if a satisfactory range cannot be found from the preferred node, then NULL is returned.
Return value
MmAllocateContiguousMemorySpecifyCacheNode returns the base virtual address for the allocated memory. If the request cannot be satisfied, the routine returns NULL.
Remarks
A kernel-mode device driver calls this routine to allocate a contiguous block of physical memory. In a non-uniform memory access (NUMA) multiprocessor system, the caller can specify a preferred node from which to allocate the memory. A node is a collection of processors that share fast access to a region of memory. In a non-NUMA multiprocessor or a single-processor system, MmAllocateContiguousMemorySpecifyCacheNode treats all memory as belonging to a single node and allocates memory from this node.
MmAllocateContiguousMemorySpecifyCacheNode allocates a block of nonpaged memory that is contiguous in physical address space. The routine maps this block to a contiguous block of virtual memory in the system address space and returns the virtual address of the base of this block. The routine aligns the starting address of a contiguous memory allocation to a memory page boundary.
Drivers must not access memory beyond the requested allocation size. For example, developers should not assume that their drivers can safely use memory between the end of their requested allocation and the next page boundary.
Because contiguous physical memory is usually in short supply, it should be used sparingly and only when necessary. A driver that must use contiguous memory should allocate this memory during driver initialization because physical memory is likely to become fragmented over time as the operating system allocates and frees memory. Typically, a driver calls MmAllocateContiguousMemorySpecifyCacheNode from its DriverEntry routine to allocate an internal buffer for long-term use, and frees the buffer just before the driver is unloaded.
Memory allocated by MmAllocateContiguousMemorySpecifyCacheNode must be freed when the memory is no longer needed. Call the MmFreeContiguousMemory routine to free memory that is allocated by MmAllocateContiguousMemorySpecifyCacheNode.
If you specify a nonzero value for the BoundaryAddressMultiple parameter, the physical address range of the allocated memory block will not cross an address boundary that is an integer multiple of this value. A driver should set this parameter to zero unless a nonzero value is required to work around a hardware limitation. For example, if a device cannot transfer data across 16-megabyte physical boundaries, the driver should specify a value of 0x1000000 for this parameter to ensure that the addresses that the device sees do not wrap around at a 16-megabyte boundary.
If you use the MmAllocateContiguousMemorySpecifyCacheNode routine on computers with large amounts of memory, the operating system's performance might severely degrade when the system tries to create a contiguous chunk of memory. This degradation is greatly reduced starting with Windows Vista SP1 and Windows Server 2008, but contiguous memory can still be expensive to allocate. For this reason, drivers should avoid repeated calls to MmAllocateContiguousMemorySpecifyCacheNode. Instead, drivers should allocate all required contiguous buffers in their DriverEntry routines and reuse these buffers.
Memory that MmAllocateContiguousMemorySpecifyCacheNode allocates is uninitialized. A kernel-mode driver must first zero this memory if it is going to make it visible to user-mode software (to avoid leaking potentially privileged contents).
Requirements
| Requirement | Value |
|---|---|
| Target Platform | Universal |
| Header | wdm.h (include Wdm.h, Ntddk.h) |
| Library | NtosKrnl.lib |
| DLL | NtosKrnl.exe |
| IRQL | IRQL <= DISPATCH_LEVEL |