wditypes.h header
This header is used by network. For more information, see:
wditypes.h contains the following programming interfaces:
Structures
| WDI_CHANNEL_MAPPING_ENTRY The WDI_CHANNEL_MAPPING_ENTRY structure defines a channel mapping entry. |
| WDI_DATA_RATE_ENTRY The WDI_DATA_RATE_ENTRY structure defines a data rate entry. |
| WDI_ETHERTYPE_ENCAPSULATION_ENTRY The WDI_ETHERTYPE_ENCAPSULATION_ENTRY structure defines an EtherType encapsulation entry. |
| WDI_TYPE_MIC The WDI_TYPE_MIC structure defines the MIC (802.11r). |
| WDI_TYPE_NONCE The WDI_TYPE_NONCE structure defines the SNonce or ANonce (802.11r). |
| WDI_TYPE_PMK_NAME The WDI_TYPE_PMK_NAME structure defines the PMKR0Name or PMKR1Name (802.11r). |
Enumerations
| WDI_ACTION_FRAME_CATEGORY The WDI_ACTION_FRAME_CATEGORY enumeration defines the action frame categories. |
| WDI_ANQP_QUERY_STATUS The WDI_ANQP_QUERY_STATUS enumeration defines the Access Network Query Protocol (ANQP) query status values. |
| WDI_ASSOC_STATUS The WDI_ASSOC_STATUS enumeration defines the association status values. |
| WDI_AUTH_ALGORITHM The WDI_AUTH_ALGORITHM enumeration defines the authentication algorithm values. |
| WDI_BLUETOOTH_COEXISTENCE_SUPPORT The WDI_BLUETOOTH_COEXISTENCE_SUPPORT enumeration defines Bluetooth coexistence support values. |
| WDI_BSS_SELECTION_FLAGS The WDI_BSS_SELECTION_FLAGS enumeration defines flags for BSS selection. |
| WDI_CAN_SUSTAIN_AP_REASON The WDI_CAN_SUSTAIN_AP_REASON enumeration defines the reasons the port is ready to receive a OID_WDI_TASK_START_AP request. |
| WDI_CIPHER_ALGORITHM The WDI_CIPHER_ALGORITHM enumeration defines the cipher algorithm values. |
| WDI_CIPHER_KEY_DIRECTION The WDI_CIPHER_KEY_DIRECTION enumeration defines the traffic directions decrypted by a cipher key. |
| WDI_CIPHER_KEY_TYPE The WDI_CIPHER_KEY_TYPE enumeration defines the cipher key types. |
| WDI_CONNECTION_QUALITY_HINT The WDI_CONNECTION_QUALITY_HINT enumeration defines the Wi-Fi connection quality hints. |
| WDI_DATA_RATE_FLAGS The WDI_DATA_RATE_FLAGS enumeration defines the data rate flags. |
| WDI_DS_INFO The WDI_DS_INFO enumeration defines values that specify whether the port is connected to the same DS that it was previously associated to. |
| WDI_ENCAPSULATION_TYPE The WDI_ENCAPSULATION_TYPE enumeration defines the Wi-Fi encapsulation types. |
| WDI_EXEMPTION_PACKET_TYPE The WDI_EXEMPTION_PACKET_TYPE enumeration defines the types of packet exemptions. |
| WDI_FIPS_MODE The WDI_FIPS_MODE enumeration defines values that specify if FIPS mode is enabled or not. |
| WDI_FTM_RESPONSE_STATUS The WDI_FTM_RESPONSE_STATUS defines the response status for a Fine Timing Measurement (FTM) request. |
| WDI_IHV_TASK_PRIORITY The WDI_IHV_TASK_PRIORITY enumeration defines IHV task priorities. |
| WDI_LCI_REPORT_STATUS The WDI_LCI_REPORT_STATUS enumeration defines the response status for an LCI report, if the report were requested in a Fine Timing Measurement (FTM) request. |
| WDI_OS_POWER_MANAGEMENT_FLAGS The WDI_OS_POWER_MANAGEMENT_FLAGS enumeration defines supported enablement scenarios of the NIC Auto Power Saver (NAPS) OS power management feature. |
| WDI_P2P_ACTION_FRAME_TYPE The WDI_P2P_ACTION_FRAME_TYPE enumeration defines the Wi-Fi Direct action frame types. |
| WDI_P2P_CHANNEL_INDICATE_REASON The WDI_P2P_CHANNEL_INDICATE_REASON enumeration defines Wi-Fi Direct channel indication reason values. |
| WDI_P2P_DISCOVER_TYPE The WDI_P2P_DISCOVER_TYPE enumeration defines the Wi-Fi Direct discovery types. |
| WDI_P2P_GO_INTERNAL_RESET_POLICY The WDI_P2P_GO_INTERNAL_RESET_POLICY enumeration defines the Wi-Fi Direct Group Owner internal reset policies. |
| WDI_P2P_LISTEN_STATE The WDI_P2P_LISTEN_STATE enumeration defines the Wi-Fi Direct listen states. |
| WDI_P2P_SCAN_TYPE The WDI_P2P_SCAN_TYPE enumeration defines the Wi-Fi Direct scan types. |
| WDI_P2P_SERVICE_DISCOVERY_TYPE The WDI_P2P_SERVICE_DISCOVERY_TYPE enumeration defines the types of service discovery. |
| WDI_PACKET_FILTER_TYPE The WDI_PACKET_FILTER_TYPE enumeration defines the packet filter types. |
| WDI_PHY_TYPE The WDI_PHY_TYPE enumeration defines the PHY types. |
| WDI_POWER_MODE_REASON_CODE The WDI_POWER_MODE_REASON_CODE enumeration defines the reasons for entering the Power Save state. |
| WDI_POWER_SAVE_LEVEL The WDI_POWER_SAVE_LEVEL enumeration defines the power save levels. |
| WDI_QOS_PROTOCOL The WDI_QOS_PROTOCOL enumeration defines Wi-Fi QOS protocols. |
| WDI_RADIO_MEASUREMENT_ACTION The WDI_RADIO_MEASUREMENT_ACTION enumeration defines the radio measurement actions. |
| WDI_ROAM_TRIGGER The WDI_ROAM_TRIGGER enumeration defines roam triggers. |
| WDI_SAE_INDICATION_TYPE The WDI_SAE_INDICATION_TYPE enumeration defines the type of information needed to continue SAE authentication with the BSSID, or notification that authentication cannot continue. |
| WDI_SAE_REQUEST_TYPE The WDI_SAE_REQUEST_TYPE enumeration defines the type of Simultaneous Authentication of Equals (SAE) request frame to send to the BSSID. |
| WDI_SAE_STATUS The WDI_SAE_STATUS enumeration defines SAE authentication failure error status codes. |
| WDI_SCAN_TRIGGER The WDI_SCAN_TRIGGER enumeration defines the scan trigger values. |
| WDI_SCAN_TYPE The WDI_SCAN_TYPE enumeration defines the scan types. |
| WDI_STOP_AP_REASON The WDI_STOP_AP_REASON enumeration defines the reasons an adapter cannot sustain 802.11 Access Point (AP) functionality on any of the PHYs. |
| WDI_WNM_ACTION The WDI_WNM_ACTION enumeration defines the message type for 802.11v BSS Transition Management action frames. |
| WDI_WPS_CONFIGURATION_METHOD The WDI_WPS_CONFIGURATION_METHOD enumeration defines WPS configuration methods. |