Bewerken

Delen via

StorPortNotification function (storport.h)

  • Artikel

The miniport driver uses the StorPortNotification routine to notify the Storport driver of certain events and conditions.

StorPortNotification takes a variable number of parameters depending on the notification type specified.

Syntax

STORPORT_API VOID StorPortNotification(
  SCSI_NOTIFICATION_TYPE NotificationType,
  PVOID                  HwDeviceExtension,
  ...                    
);

Parameters

NotificationType

Specifies the notification type, which can be one of the following values.

Notification type Description
BufferOverrunDetected This notification type has no arguments and gives the miniport driver an opportunity to bugcheck the system if it detects a corruption.
BusChangeDetected Indicates that a target device might have been added or removed from a dynamic bus. To use this notification type, include an optional PathId parameter to indicate the SCSI port or bus where the change was detected. 
VOID StorPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ UCHAR                  PathId
);
IoTargetRequestServiceTime Indicates to Storport the amount of time that was required to process a specified request. 
VOID StorPortNotification(
  _In_ SCSI_NOTIFICATION_TYPE NotificationType,
  _In_ PVOID                  HwDeviceExtension,
  _In_ ULONGLONG              Duration,
  _In_ PSCSI_REQUEST_BLOCK    Srb
);

Duration [in]

The duration of the service time required for Srb in 100 nanosecond units.

Srb [in]

The request block to set the service time for.
LinkDown Indicates that the link is down and will probably be down for some time. StorPort will pause the adapter in response to this notification.
LinkUp Indicates that the link has been restored. StorPort restarts the adapter so that it can resume operation in response to this notification. Miniport drivers should not send this notification unless the link is down.
QueryTickCount This notification type returns a LARGE_INTEGER that holds the value from KeQueryTickCount. The value returned in TickCount is the count of the interval timer interrupts that have occurred since the system was booted 
VOID StorPortNotification(
  _In_    SCSI_NOTIFICATION_TYPE NotificationType,
  _In_    PVOID                  HwDeviceExtension,
  _Inout_ PLARGE_INTEGER         TickCount
);
RequestComplete Indicates that the given SRB has finished. After this notification is sent, the port driver owns the request. The Srb parameter represents a pointer to the completed SCSI request block. The miniport driver must not attempt to access the request in Srb, and it must not pass Srb to another routine. 
VOID StorPortNotification(
  _In_ SCSI_NOTIFICATION_TYPE NotificationType,
  _In_ PVOID                  HwDeviceExtension,
  _In_ PSCSI_REQUEST_BLOCK    Srb
);
RequestTimerCall Indicates that the miniport driver requires the port driver to call the miniport driver's HwStorTimer routine in the requested number of microseconds. 
VOID StorPortNotification(
  _In_ SCSI_NOTIFICATION_TYPE NotificationType,
  _In_ PVOID                  HwDeviceExtension,
  _In_ PHW_TIMER              HwStorTimer,
  _In_ ULONG                  MiniportTimerValue
);

HwStorTimer [in]

A pointer to a timer routine that is called after the interval of time that is specified in MiniportTimerValue.

MiniportTimerValue [in]

Indicates the interval after which the timer routine pointed to by HwStorTimer is called. This is a positive value specified in microseconds. A value of 0 will cancel the timer. The system timer resolution is approximately 10 milliseconds.
ResetDetected Indicates that the HBA has detected a reset on the bus. After this notification is sent, the miniport driver is still responsible for completing any active requests. The port driver will manage all required bus-reset delays.
WMIEvent Indicates that the miniport driver has detected an event for which one or more WMI data consumers are registered. Note that the WmiEvent parameter is limited to a maximum of 128 bytes. If WmiEvent is larger than 128 bytes, it will be ignored. 
VOID StorPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,
  _In_     PVOID                  HwDeviceExtension,
  _In_     PWNODE_EVENT_ITEM      WMIEvent,
  _In_     UCHAR                  PathId,
  _In_opt_ UCHAR                  TargetId,
  _In_opt_ UCHAR                  Lun
);

WMIEvent [in]

A pointer to event structures that have information about a WMI event that is detected by the miniport driver.

PathId [in]

Indicates the SCSI port or bus for the request. Set this parameter to 0xff for an adapter device. Otherwise, set to a valid path ID.

TargetId [in, optional]

Indicates the target controller or device on the bus. This parameter is not used when the event is for an adapter.

Lun [in, optional]

Indicates the logical unit number of the device. This parameter is not used when the event is for an adapter.
WMIReregister Indicates that the miniport driver has changed the data items or the number of instances of a given data block that was previously registered by calling IoWMIRegistrationControl. 
VOID StorPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,
  _In_     PVOID                  HwDeviceExtension,
  _In_     UCHAR                  PathId,
  _In_opt_ UCHAR                  TargetId,
  _In_opt_ UCHAR                  Lun
);

PathId [in]

Indicates the SCSI port or bus for the request. Set this parameter to 0xff for an adapter device. Otherwise, set to a valid path ID.

TargetId [in, optional]

Indicates the target controller or device on the bus. This parameter is not used when registration is for an adapter.

Lun [in, optional]

Indicates the logical unit number of the device. This parameter is not used when registration is for an adapter.

HwDeviceExtension

A pointer to the hardware device extension. This is a per HBA storage area that the port driver allocates and initializes on behalf of the miniport driver. Miniport drivers usually store HBA-specific information in this extension, such as the state of the HBA and the mapped access ranges for the HBA. This area is available to the miniport driver immediately after the miniport driver calls StorPortInitialize. The port driver frees this memory when it removes the device.

...

Additional Parameters.

Return value

None.

Remarks

StorPortNotification is a polymorphic function that handles many different types of requests, making it difficult to annotate in a manner that would cover all possible uses. Because StorPortNotification returns VOID, the scanning engine should assume the LockHandle was acquired as asked.

Requirements

Requirement Value
Target Platform Universal
Header storport.h (include Storport.h)
Library Storport.lib
DDI compliance rules StorPortNotification2(storport), StorPortStatusPending, StorPortTimer(storport)

See also

StorPortInitialize