ScsiPortNotification function (srb.h)

Artikel
01/04/2022

The ScsiPortNotification routine informs the operating system-specific port driver of certain events, such as when a miniport driver completes a request or is ready to start another SRB, as well as when the host bus adapter (HBA) indicates certain SCSI error conditions that occurred during an operation.

Note

The SCSI port driver and SCSI miniport driver models may be altered or unavailable in the future. Instead, we recommend using the Storport driver and Storport miniport driver models.

Syntax

SCSIPORT_API VOID ScsiPortNotification(
  SCSI_NOTIFICATION_TYPE NotificationType,
  PVOID                  HwDeviceExtension,
  ...                    
);

Parameters

NotificationType

Specifies the type of notification. See Remarks.

HwDeviceExtension

Pointer to the hardware device extension. This is a per-HBA storage area that the port driver allocates and initializes on behalf of the miniport driver. Miniport drivers usually store HBA-specific information in this extension, such as the state of the HBA and the HBA's mapped access ranges. This area is available to the miniport driver in the DeviceExtension->HwDeviceExtension member of the HBA's device object immediately after the miniport driver calls ScsiPortInitialize. The port driver frees this memory when it removes the device.

...

Variadic arguments for this routine. The number and type of arguments depend on NotificationType. See Remarks.

Return value

None

Remarks

The ScsiPortNotification routine has a different set of optional parameters associated with each NotificationType. The list of possible values for NotificationType follows, along with descriptions for each value.

NotificationType = RequestComplete

Indicates that the given Srb has finished. If this value is set, ScsiPortNotification requires one additional parameter: the address of the SRB. After this notification, the operating system-specific port driver owns the request. The miniport driver must not access the Srb, and it must not pass the Srb to another routine (such as ScsiPortLogError).

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,   // RequestComplete
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PSCSI_REQUEST_BLOCK    Srb
);
```
NotificationType = NextRequest

Indicates the miniport driver is ready for another request to a target that is not currently busy. This notification should be sent by the miniport driver as soon as the driver is ready for another request. Usually, this notification is sent from the HwScsiStartIo routine but, sometimes, from the HwScsiInterrupt (or HwScsiEnableInterruptsCallback) routine.
NotificationType = NextLuRequest

Indicates that the HBA is ready for another request for the specified logical unit. If this value is set, ScsiPortNotification requires three additional parameters: (1) the path ID, (2) the target ID, and (3) the logical unit number. This value should be used only if the HBA can queue multiple requests and support auto-request sense or tagged queuing.

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,   // NextLuRequest
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_                        PathId,
  _In_opt_                        TargetId,
  _In_opt_                        Lun
);
```
NotificationType = ResetDetected

Indicates that the HBA has detected a reset on the SCSI bus. After this notification, the miniport driver is still responsible for completing any active requests. The SCSI port driver will manage all required bus-reset delays.
NotificationType = CallEnableInterrupts

Indicates that the miniport driver requires the operating system-specific port driver to call the miniport driver's HwScsiEnableInterruptsCallback routine. If this value is set, ScsiPortNotification requires an additional parameter: the entry point for the HwScsiEnableInterruptsCallback. The miniport driver's HwScsiInterrupt routine makes this call after disabling interrupts on the HBA, to defer some interrupt-driven I/O processing if the HBA requires polling or stalling in the ISR. While the callback runs, system interrupts remain enabled but the miniport driver's HwScsiInterrupt routine will not be called. The HwScsiEnableInterruptsCallback is responsible for completing the deferred I/O processing and for calling ScsiPortNotification again with CallDisableInterrupts and the miniport driver's HwScsiDisableInterruptsCallback entry point.

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,           // CallEnableInterrupts
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PHW_INTERRUPT          HwScsiXxxInterruptsCallback
);
```
NotificationType = CallDisableInterrupts

Indicates that the miniport driver requires the operating system-specific port driver to call the miniport driver's HwScsiDisableInterruptsCallback routine. If this value is set, ScsiPortNotification requires an additional parameter: the entry point for the HwScsiDisableInterruptsCallback. While this callback runs, it cannot be preempted by an interrupt except from a device with a higher priority interrupt than the HBA. In this callback, the miniport driver reenables interrupts on the HBA.

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,          // CallDisableInterrupts
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PHW_INTERRUPT          HwScsiXxxInterruptsCallback
);
```
NotificationType = RequestTimerCall

Indicates that the miniport driver requires the operating system-specific port driver to call the miniport driver's HwScsiTimer routine in the requested number of microseconds. If this value is set, ScsiPortNotification requires two additional parameters: (1) the entry point for the miniport driver's HwScsiTimer routine, and (2) a MiniportTimerValue interval, in microseconds. Note that the resolution of the system timer is approximately 10 milliseconds.

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,    // RequestTimerCall
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PHW_TIMER              HwScsiTimer,
  _In_opt_ ULONG                  MiniportTimerValue
);
```
NotificationType = BusChangeDetected

Indicates that a target device might have been added or removed from a dynamic bus. If this value is set, ScsiPortNotification requires an additional parameter: the path ID of the bus on which the change was detected. After this notification, the port driver reenumerates the bus by issuing INQUIRY commands. Bus enumeration is time-consuming and ties up the bus, so a miniport driver should not send this notification unnecessarily.

Syntax:
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,    // BusChangeDetected
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ UCHAR                  PathId
);
```
NotificationType = WMIEvent

Indicates that the miniport driver has detected an event for which one or more WMI data consumers is registered. If this value is set, ScsiPortNotification requires at least three additional arguments: (1) a pointer to a WMI event structure, (2) the size of the event structure, and (3) the path ID of the target device if the event originated from a device, or 0xFF if the event originated from the adapter. If (3) is a path ID, ScsiPortNotification requires two additional arguments: (4) the target ID, and (5) the logical unit number (LUN) of the target device.

Syntax for PathId != 0xFF
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,    // WMIEvent
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PVOID                  WMIEvent,
  _In_opt_ UCHAR                  PathId,              // != 0xFF
  _In_opt_ UCHAR                  TargetId,
  _In_opt_ UCHAR                  Lun
);
```
Syntax for PathId = 0xFF
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,    // WMIEvent
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ PVOID                  WMIEvent,
  _In_opt_ UCHAR                  PathId               // 0xFF
);
```
NotificationType = WMIReregister

Indicates that the miniport driver has changed the data items or the number of instances of a given data block previously registered by calling IoWMIRegistrationControl. If WMIReregister is set, ScsiPortNotification requires at least two additional arguments: (1) the path ID of the target device to reregister that device, or 0xFF to reregister the adapter. If (1) is a path ID, ScsiPortNotification requires two additional arguments: (2) the target ID, and (3) the logical unit number (LUN) of the target device.

Syntax for PathId != 0xFF
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,    // WMIReregister
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ UCHAR                  PathId,             // != 0xFF
  _In_opt_ UCHAR                  TargetId,
  _In_opt_ UCHAR                  Lun
);
```
Syntax for PathId = 0xFF
```
VOID ScsiPortNotification(
  _In_     SCSI_NOTIFICATION_TYPE NotificationType,   // WMIReregister
  _In_     PVOID                  HwDeviceExtension,
  _In_opt_ UCHAR                  PathId              // 0xFF
);
```

Every miniport driver must call ScsiPortNotification twice for each call to the miniport driver's HwScsiStartIo routine with an SRB that the miniport driver completes successfully. First, the miniport driver calls ScsiPortNotification with the NotificationType of NextRequest or with NextLuRequest if the miniport driver supports tagged queuing or multiple requests per LU. Then, the miniport driver calls ScsiPortNotification with the NotificationType of RequestComplete and the request that it has just satisfied.

A miniport driver's HwScsiInterrupt routine is most likely to call ScsiPortNotification with the NotificationType of ResetDetected.

If an HBA requires the miniport driver to use more than a millisecond processing interrupt-driven I/O operations, its HwScsiInterrupt routine should disable interrupts on the HBA and call ScsiPortNotification with CallEnableInterrupts and a driver-supplied HwScsiEnableInterruptsCallback routine. This routine, in turn, calls ScsiPortNotification with CallDisableInterrupts and the corresponding driver-supplied HwScsiDisableInterruptsCallback.

A miniport driver that is registered as a WMI data provider can call ScsiPortNotification with WMIEvent to post an event for which it has previously received an enable request. The port driver queues the event in the interrupt data area of the miniport driver's device extension for later processing at a lower IRQL. Because only a limited number of events can be queued at one time, the miniport driver should use WMIEvent to signal exceptional rather than routine conditions, and it should give the port driver time to get back to DISPATCH_LEVEL between postings, to prevent events from being lost.

Requirements

Requirement	Value
Target Platform	Universal
Header	srb.h (include Miniport.h, Scsi.h)
Library	Scsiport.lib; Storport.lib
IRQL	(See Remarks section)

Delen via

ScsiPortNotification function (srb.h)

Syntax

Parameters

Return value

Remarks

Requirements

See also

Feedback

Aanvullende resources