Bewerken

Delen via

Replay Option (Distributed Replay Administration Tool)

  • Artikel

Applies to: SQL Server 2016 (13.x), SQL Server 2017 (14.x), and SQL Server 2019 (15.x)

Important

SQL Server Distributed Replay is not available with SQL Server 2022 (16.x).

The Microsoft SQL Server Distributed Replay administration tool, DReplay.exe, is a command-line tool that you can use to communicate with the distributed replay controller. This topic describes the replay command-line option and corresponding syntax.

The replay option initiates the event replay stage, in which the controller dispatches replay data to the specified clients, launches the distributed replay and synchronizes the clients. Optionally, each client participating in the replay can record the replay activity and save a result trace file locally.

For more information about the syntax conventions that are used with the administration tool syntax, see Transact-SQL syntax conventions.

Syntax


dreplay replay [-m controller] -d controller_working_dir [-o]  
    [-s target_server] -w clients [-c config_file]  
    [-f status_interval]

Parameters

-m controller
Specifies the computer name of the controller. You can use "localhost" or "." to refer to the local computer.

If the -m parameter isn't specified, the local computer is used.

-d controller_working_dir
Specifies the directory on the controller where the intermediate file will be stored. The -d parameter is required.

The following requirements apply:

  • The directory must reside on the controller.

  • You must specify the full path, starting with a drive letter (for example, c:\WorkingDir).

  • The path must not end with a backslash "\".

  • UNC paths aren't supported.

-o
Captures the clients' replay activity and saves it to a result trace file in the path specified by the <ResultDirectory> element in the client configuration file, DReplayClient.xml.

When the -o parameter isn't specified, the result trace file isn't generated. The console output returns summary information at the end of replay, but no other replay statistics are available.

-s target_server
Specifies the target instance of SQL Server that the distributed workload should be replayed against. You must specify this parameter in the format server_name[\instance name].

You can't use "localhost" or "." as the target server.

The -s parameter isn't required if the <Server> element is specified in the <ReplayOptions> section of the replay configuration file, DReplay.exe.replay.config.

If the -s parameter is used, the <Server> element in the <ReplayOptions> section of the replay configuration file will be ignored.

-w clients
This required parameter is a comma-separated list (without spaces) that specifies the computer names of clients that should participate in the distributed replay. IP addresses aren't allowed. Be aware that the clients must already be registered with the controller.

Note

Each client registers with the controller that is specified in the client configuration file when the client service starts.

-c config_file
Is the full path of the replay configuration file; used to specify the location when it's stored in a different location.

The -c parameter isn't required if you want to use the default values of the replay configuration file, DReplay.exe.replay.config.

-f status_interval
Specifies the frequency (in seconds) at which to display the status.

If -f isn't specified, the default interval is 30 seconds.

Examples

In this example, the distributed replay derives much of its behavior from a modified replay configuration file, DReplay.exe.replay.config.

  • The -m parameter specifies that a computer named controller1 acts as the controller. The computer name must be specified when the controller service is running on a different computer.

  • The -d parameter specifies the location of the intermediate file on the controller, c:\WorkingDir.

  • The -o parameter specifies that each specified client capture the replay activity and save it to a result trace file. Note: The <ResultTrace> element in the configuration file can be used to specify if row count and result set be recorded.

  • The -w parameter specifies that computers client1 through client4 participate as clients in the distributed replay.

  • The -c parameter is used to point to the modified configuration file, DReplay.exe.replay.config.

  • The -s parameter isn't required because the <Server> element is specified in the <ReplayOptions> element of the replay configuration file, DReplay.exe.replay.config.

The event replay stage is initiated with the following syntax, when the administration tool is run from a different computer than the controller:

dreplay replay -m controller1 -d c:\WorkingDir -o -w client1,client2,client3,client4 -c c:\DReplay.exe.replay.config

To specify a synchronous sequencing mode, the <SequencingMode> element of the DReplay.exe.replay.config file is set equal to the value synchronization. The <ResultTrace> section of the replay configuration file is modified to specify that row count be recorded. These changes are shown in the following XML example:

<?xml version='1.0'?> 
<Options> 
    <ReplayOptions> 
        <Server>server_name\replay_target_instance</Server> 
        <SequencingMode>synchronization</SequencingMode> 
        <ConnectTimeScale></ConnectTimeScale> 
        <ThinkTimeScale></ThinkTimeScale> 
        <HealthmonInterval>60</HealthmonInterval> 
        <QueryTimeout>3600</QueryTimeout> 
        <ThreadsPerClient></ThreadsPerClient> 
    </ReplayOptions> 
    <OutputOptions> 
        <ResultTrace> 
            <RecordRowCount>Yes</RecordRowCount> 
            <RecordResultSet>No</RecordResultSet> 
        </ResultTrace> 
    </OutputOptions> 
</Options>

To specify a stress sequencing mode, the <SequencingMode> element of the DReplay.exe.replay.config file is set equal to the value stress. The <ConnectTimeScale> and <ThinkTimeScale> elements are set to the value 50 (to specify 50 percent). For more information about connect time and think time, see Configure Distributed Replay. These changes are shown in the following XML example:

<?xml version='1.0'?> 
<Options> 
    <ReplayOptions> 
        <Server>server_name\replay_target_instance_name</Server> 
        <SequencingMode>stress</SequencingMode> 
        <ConnectTimeScale>50</ConnectTimeScale> 
        <ThinkTimeScale>50</ThinkTimeScale> 
        <HealthmonInterval>60</HealthmonInterval> 
        <QueryTimeout>3600</QueryTimeout> 
        <ThreadsPerClient></ThreadsPerClient> 
    </ReplayOptions> 
    <OutputOptions> 
        <ResultTrace> 
            <RecordRowCount>Yes</RecordRowCount> 
            <RecordResultSet>No</RecordResultSet> 
        </ResultTrace> 
    </OutputOptions> 
</Options>

Permissions

You must run the administration tool as an interactive user, as either a local user or a domain user account. To use a local user account, the administration tool and controller must be running on the same computer.

For more information, see Distributed Replay Security.

See also