Disable-UMIPGateway

Reference

Module:: ExchangePowerShell

Applies to:: Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

This cmdlet is available only in on-premises Exchange.

Use the Disable-UMIPGateway cmdlet to disable a Unified Messaging (UM) IP gateway.

For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.

Syntax

Disable-UMIPGateway
       [-Identity] <UMIPGatewayIdParameter>
       [-Confirm]
       [-DomainController <Fqdn>]
       [-Immediate <Boolean>]
       [-WhatIf]
       [<CommonParameters>]

Description

The status variable for a UM IP gateway can be used to enable or disable call answering destined for the IP gateway. The Disable-UMIPGateway cmdlet disables a UM IP gateway in Active Directory by modifying its status variable. After this task is completed, the UM IP gateway no longer answers incoming calls or makes outgoing calls.

You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.

Examples

Example 1

Disable-UMIPGateway -Identity MyUMIPGateway

This example disables the UM IP gateway MyUMIPGateway and stops it from accepting incoming calls from the IP gateway.

Example 2

Disable-UMIPGateway -Identity MyUMIPGateway -Immediate $true

This example disables the UM IP gateway MyUMIPGateway and disconnects all current calls immediately.

Parameters

-Confirm

The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.

Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax: -Confirm:$false.
Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.

This cmdlet has a built-in pause, so use -Confirm:$false to skip the confirmation.

Type:	SwitchParameter
Aliases:	cf
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-DomainController

The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.

Type:	Fqdn
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-Identity

The Identity parameter specifies the identifier for the UM IP gateway being disabled. This is the directory object ID for the UM IP gateway.

Type:	UMIPGatewayIdParameter
Position:	1
Default value:	None
Required:	True
Accept pipeline input:	True
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-Immediate

The Immediate parameter specifies whether the Mailbox server running the Microsoft Exchange Unified Messaging service drops incoming calls associated with this UM IP gateway immediately or waits for the current calls to finish processing.

Type:	Boolean
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

-WhatIf

The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.

Type:	SwitchParameter
Aliases:	wi
Position:	Named
Default value:	None
Required:	False
Accept pipeline input:	False
Accept wildcard characters:	False
Applies to:	Exchange Server 2010, Exchange Server 2013, Exchange Server 2016

Inputs

Input types

To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.

Outputs

Output types

To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.

Delen via