LINECALLREASON (Windows Embedded CE 6.0)
1/6/2010
These bit-flag constants describe the reason for a call.
The following table shows the LINECALLREASON constants.
| Value | Decription |
|---|---|
LINECALLREASON_CALLCOMPLETION = 0x00000080 |
The call was the result of a call completion request. |
LINECALLREASON_CAMPEDON = 0x00004000 |
The call was camped on the address. Usually, it appears initially in the onhold state, and can be switched to using lineSwapHold. If an active call becomes idle, the camped-on call may change to the offering state and the device start ringing. TAPI version 2.0 and later. |
LINECALLREASON_DIRECT = 0x00000001 |
This is a direct incoming or outgoing call. |
LINECALLREASON_FWDBUSY = 0x00000002 |
This call was forwarded from another extension that was busy at the time of the call. |
LINECALLREASON_FWDNOANSWER = 0x00000004 |
The call was forwarded from another extension that didn't answer the call after some number of rings. |
LINECALLREASON_FWDUNCOND = 0x00000008 |
The call was forwarded unconditionally from another number. |
LINECALLREASON_INTRUDE = 0x00001000 |
The call intruded onto the line, either by a call completion action invoked by another station or by operator action. Depending on switch implementation, the call may appear either in the connected state, or conferenced with an existing active call on the line. TAPI version 1.4 and later. |
LINECALLREASON_PARKED = 0x000002000 |
The call was parked on the address. Usually, it appears initially in the onhold state. TAPI version 1.4 and later. |
LINECALLREASON_PICKUP = 0x00000010 |
The call was picked up from another extension. |
LINECALLREASON_REDIRECT = 0x00000040 |
The call was redirected to this station. |
LINECALLREASON_REMINDER = 0x00000200 |
The call is a reminder, or "recall", that the user has a call parked or on hold for potentially a long time. |
LINECALLREASON_ROUTEREQUEST = 0x00008000 |
The call appears on the address because the switch needs routing instructions from the application. The application should examine the CalledID member in LINECALLINFO, and use the lineRedirect function to provide a new dialable address for the call. If the call is to be blocked instead, the application may call lineDrop. If the application fails to take action within a switch-defined timeout period, a default action will be taken. A service provider can use this constant only if the negotiated version on the line is 2.0 or later. Otherwise the service provider should substitute LINECALLREASON_UNAVAIL. TAPI version 2.0 and later. |
LINECALLREASON_TRANSFER = 0x00000100 |
The call has been transferred from another number. |
LINECALLREASON_UNAVAIL = 0x00000800 |
The reason for the call is unavailable and will not become known later. |
LINECALLREASON_UNKNOWN = 0x00000400 |
The reason for the call is currently unknown but may become known later. |
LINECALLREASON_UNPARK = 0x00000020 |
The call was retrieved as a parked call. |
Remarks
These constants cannot be extended. All 32 bits are reserved.
The LINECALLREASON constants are used in the dwReason member of the LINECALLINFO data structure.
Requirements
| Header | tapi.h |
| Windows Embedded CE | Windows CE 3.0 and later |
See Also
Reference
TAPI Constants
lineDrop
lineSwapHold
lineRedirect
LINECALLINFO