次の方法で共有

OpsMgr 2012: Discovering a network device

  • [アーティクル]

Comments

  • Anonymous
    January 01, 2003
    The comment has been removed

  • Anonymous
    January 01, 2003
    Same question as @Brett ...  How can we supress alerts behind a monitored network device if that device is down.  I clearly remember being told at an MMS presentation for SCOM 2012 network monitoring that this would be possible.

  • Anonymous
    January 01, 2003
    @Brett is there any update on your issue?  I can't believe more people aren't having the issue with loss of network connectivity to a remote site causing false SCOM alerts.

  • Anonymous
    January 01, 2003
    Kevin, are there plans for adding support for more devices?  I have a number of Cisco MDS switches but only 1 of the 3 models I use are supported so far.

  • Anonymous
    January 01, 2003
    The comment has been removed

  • Anonymous
    January 01, 2003
    When I created my initial network discovery I got one instance of each node. Now this morning, I am seeing a second instance of a few nodes. All the information about the node is the same except the System Name/Device Key fields which corresponds to a MAC address on the device. When the device was initially discovered, the System Name/Device Key was the MAC corresponding to the IP for the VLAN interface I used in the discovery. The new instance of the device has a MAC corresponding to the Bridge ID address. I'm not sure which one to delete or how to handle the duplication otherwise.

    • Anonymous
      July 17, 2017
      I have seen this scenario in other customers. In the customer that I am working the devices are being replaced by equipment from the same manufacturer, however, more current. With this, when SCOM does the rediscover, two devices with the same IP appear. Because? The new device is now available for monitoring. Then the customer to remove the old device and sets up the monitoring for the new device (router). Something absolutely normal!The process of monitoring and refinement is constant and can not stop.And an important point to note is the MAC address of each device. Because even though they are identical to the manufacturer, MAC Address is unique. Tips: Observe the device discovery date, MAC Address, and interfaces, because a new device does not have its ports enabled by default.

  • Anonymous
    January 01, 2003
    When Installing OpsMgr 2012 R2 on Server 2012 R2, firewall rules necessary for network monitoring are created but left disabled. I enabled them and the discovery worked successfully. The firewall rule names are Operations Manager SNMP Response, Operations Manager SNMP Trap Listener & Operations Manager Ping Response

  • Anonymous
    January 01, 2003
    Vishnu - YOU ROCK!

  • Anonymous
    January 01, 2003
    You need to run the tasks to enable port monitoring.

  • Anonymous
    July 21, 2011
    Great job on this functionality but still disappointed that the NW Device is referenced by IP and not sysName ("MIB 2 System Name").  I know you can add that column to the state views but performance views will be less inviting since you can't add the column there.  Dashboards would benefit from sysName too.  Do alert descriptions contain the sysName in addition to the ip address?  If not, assuming sealed MP's, that's going to create some unfortunate work for some of us whose users want alerts with host/system names and not IP's.  I do love the look though.

  • Anonymous
    July 21, 2011
    Can you do a blog post on discovering a Linux/Unix server?

  • Anonymous
    July 22, 2011
    Hi Kevin, maybe something to mention: Disable (or change) the firewall settings of the management server(s) where you are kicking off the network discovery. I noticed that the discovery process will not give you any error/warning event on this. It will simply tell you no devices are discovered... Michel

  • Anonymous
    August 05, 2011
    Have you messed with any of the interface overrides for the network devices yet? By default they are all disabled. I have been trying to figure out how to turn on interface monitoring, however I have yet to find discoveries for this. The monitors are there, which makes me interested to see how much QA the dev team performed to support more SNMP GUID Monitors in this version. As aways, great posts. don't know what I would do without some of them.

  • Anonymous
    August 05, 2011
    The comment has been removed

  • Anonymous
    December 13, 2011
    Hi All, Is there any power shell script avialable for discovering Network devices in SCOM 2012

  • Anonymous
    January 09, 2012
    The comment has been removed

  • Anonymous
    February 07, 2013
    Hello, If ping is blocked at the network device end, will SCOM be able to discover the device?

  • Anonymous
    June 25, 2013
    Hi All, Kevin, I’m running scom2012SP1 on a Windows2012 server and I can’t get any network devices working with SNMP. The message which I get is “No response SNMP” but I am sure that the ip/community string is correct. In scom2007R2 on win2k8 is working fine. Of course I added the ip adress of the scom server in the network devices, but it is still not working! Even when I disabled the windows Firewall.(I thought maybe I made the wrong exclusion) The SNMP feature are also installed and the SNMP trap service is disabled. Hope you can help me!

  • Anonymous
    September 17, 2013
    "No Response SNMP" message while discovering a cisco switch with SNMPv3 enabled. SCOM2012 Some of the same model/OS switches with the same configuration were discovered but others sowing the above message. No configuration difference at all. Any suggestions ?

  • Anonymous
    May 30, 2014
    Pingback from SCOM QUICK Install | config.re

  • Anonymous
    June 06, 2014
    I thought ICMP & SNMP access method required both to successful else it will fail? Above you state 'as long as one of those is available we consider the device up'

  • Anonymous
    December 01, 2014
    I opened a Microsoft case and got a fix for the duplicate device issue. It is a private fix so I suggest opening another ticket and requesting the fix. The issue is resolved with an updated version of he "ic.iftable.asl" file

  • Anonymous
    February 03, 2015
    There are several really good blogs out there which document some of the struggles and workarounds with

  • Anonymous
    March 10, 2015
    Hi Kevin,
    I always follow your article and I love it . I just have one question on Reporting on Networking devices .

    I am trying to generate a report for "Interface Traffic Volume " and the report is blank . Does it require the Rules to be enabled by override?

  • Anonymous
    March 11, 2015
    Has anyone solved the issue Bret was asking about?

  • Anonymous
    August 10, 2015
    The comment has been removed

  • Anonymous
    October 28, 2015
    The comment has been removed

  • Anonymous
    February 19, 2016
    Hi Everyone,

    I have a problem with network discovery. I previously discovered a Cisco device that is certified by SCOM, but for now, its not discovering as certified. Have any of you encountered this issue?

    Please help and advise

  • Anonymous
    May 12, 2016
    Great stuff! Now the tough part, I need to create a class/group of network interfaces on like network devices for monitoring. I followed the directions at http://blogs.catapultsystems.com/cfuller/archive/2013/06/20/how-to-add-monitoring-for-a-port-or-interface-on-a-network-device-in-operations-manager-2012-scom-sysctr/ but that isn't dynamic enough for me. any help would be much appreciated.

    • Anonymous
      May 12, 2016
      Steve - I wrote up this process right here:https://blogs.technet.microsoft.com/kevinholman/2016/04/20/writing-a-custom-class-for-your-network-devices/

  • Anonymous
    June 17, 2016
    Hi Kevin,I have SCOM2012R2 and i want to catch alerts from vRops 6.2 .I can't discover the vROPS .There is not firewall between the vROPS and the SCOM.Also ,i can see the snmp trap from the vROPS on the SCOM server with wireshark ,but i can't discover it.Need help please.Best regards

  • Anonymous
    June 21, 2016
    Is there a way to discover a windows computer that is running an application that generates SNMP traps. Discovering the windows computer fails because it is a windows computer even if SNMP is responding correctly. In our case the application generates SNMP traps only and SCOM will only accept the trap if it comes from a previously discovered device.Would it work to have the discovery work against a device using the same IP as the server will get after the discovery? This way I could discover the bogus device at the IP and then replace the real server at the same IP.Any other ideas?

  • Anonymous
    June 25, 2017
    Hello Kevin,Hope You are doing Good!I'm try to discover the NetScaler devices. However I get ""No Response SNMP"I have Verified the port connectivity and Community string.The IP address of the Management severs have been added in the netscaler device,which needs to be Monitored.Could you please Suggest some troubleshooting Steps.

  • Anonymous
    September 10, 2017
    As for my problem: Devices have been inserted according to procedure, but collection of link counters (interface usage and port usage) are not visible on the console. The ports I want to monitor were enabled by the task and also entered into the critical interfaces group. The other counters for memory and ping are fully visible. Have some punctual tip. Thanks for your feedback.

  • Anonymous
    December 06, 2017
    Hi,We have a Dell OME server ( monitoring physical dell servers ) which is forwarding the SNMP V1 traps to SCOM 21012 R2. But the alerts in the SCOM are dropping off as SNMP V1 has an agent address field which contains the source IP "Dell physical server " not off the Dell OME server.Is there any configuration in the SCOM to receive the SNMP V1 alert and disregard the "Agent address", so that it does not drop off the alerts / traps.Please assist. It would be a great help !

  • Anonymous
    December 08, 2017
    Hi Kevin, Do you know of a way to monitor for packet loss on network devices?

  • Anonymous
    January 11, 2018
    Kevin,could you please explain how SCOM picks the device key from the device? Which MAC of which port will be taken? I have a customer where the NW guys feel that this is kind of random and not the expected MAC of the port we use the IP address from...Many thanks,Patrick