Partager via

KDC_ERR_PREAUTH_REQUIRED vs. KDC_ERR_PREAUTH_FAILED

  • Article

         I often seen network admins look at a network trace and say we have a lot of authentication failures and point to the error – KDC_ERR_PREAUTH_REQUIRED. I have spent time educating on why this is not an authentication failure but instead the default behavior. The KDC (Key Distribution Center) requires all accounts to use pre-authentication. However, pre-authentication can be disabled for individual accounts when necessary for compatibility with other implementations of the protocol.

How to disable pre-authentication?

If the box “Do not require Kerberos pre-authentication” was checked on the user account properties then we would never see the error “KDC_ERR_PREAUTH_REQUIRED” message in a trace.

 

 Let us look at the initial user authentication process using network traces.

FRAME 1:

  

 

The above Frame shows you an AS_Request being sent to the domain controller - 192.168.1.25 from Client machine 192.168.1.25. As you observe there is nothing sent along with PaData.

As a result the DC replies with the below error in the below frame – KDC_ERR_PREAUTH_REQUIRED.

FRAME 2:

  

So the client then sends the AS_REQUEST again with the pre-authentication data as show in the below frame. – KrbEncTimestamp: Encrypted Time Stamp Pre-Authentication.

FRAME 3:

  

FRAME 4:

 

As see above the KDC_ERR_PREAUTH_REQUIRED is not exactly an authentication failure. If the Kerberos authentication fails (for example bad password) then you would see “KDC_ERR_PREAUTH_FAILED” in the trace as shown below.

FRAME 5:

Below is the error you will see in a trace when Authentication fails for the user – Now it’s time you investigate. J

Enable Auditing, and Kerberos logging if required.

 

 

 

 I hope its better understood now and there is enough clarity now when you look at network captures that shows KDC_ERR_PREAUTH_REQUIRED & KDC_ERR_PREAUTH_FAILED frames in network traces.

Comments

  • Anonymous
    January 01, 2003
    @Harmandeep - The Frame 1 shows that the client does not send pre-auth data ( KrnEncTimeStamp ) by default and in fram 3 it sends the pre-auth since it receievd pre-auth required from DC ( Frame 2 ).
  • Anonymous
    January 01, 2003
    The comment has been removed
  • Anonymous
    March 12, 2014
    That makes sense!! Thanks!
  • Anonymous
    January 15, 2015
    Thanks for sharing valuable information.

    As per FRAME 1, lsass.exe process is AS_REQ with preauth data. How can i set the same i.e. force a client system not to send the preauth data to a discovered d.c. ?
    • Anonymous
      October 25, 2016
      By default the client does not send pre-auth data in Frame 1.
  • Anonymous
    October 09, 2015
    How do you capture these details. Can you tell me the tool to trace the kerberos authentication.
  • Anonymous
    November 15, 2015
    Hi Arasuraja -- You could use netmon or Message Analyzer
  • Anonymous
    March 03, 2016
    Hello,

    great article.
    We get the 0x19 KDC_ERR_PREAUTH_REQUIRED Error in a mixed environment (Novell DSFW + WinSrv2xxx - perhaps this is not relevant.

    Authentication works and there are no issues. However, if we enable Kerberos logging, after each user-login an Error is produced that shows very weird Client-Times.
    a) the time is ok on server and client
    b) the times jump around: once it is 1987, then 2031 ...

    Do you have any explanation for this?
    ...
    Client Time: 16:18:46.0000 3/2/1976 Z
    Server Time: 13:53:18.0000 3/3/2016 Z
    Error Code: 0x19 KDC_ERR_PREAUTH_REQUIRED