Set-IPBlockListProvidersConfig
This cmdlet is available or effective only on Edge Transport servers in on-premises Exchange.
Use the Set-IPBlockListProvidersConfig cmdlet to modify the settings that affect all IP Block list providers that are configured on an Edge Transport server.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Set-IPBlockListProvidersConfig
[-BypassedRecipients <MultiValuedProperty>]
[-Confirm]
[-DomainController <Fqdn>]
[-Enabled <Boolean>]
[-ExternalMailEnabled <Boolean>]
[-InternalMailEnabled <Boolean>]
[-WhatIf]
[<CommonParameters>] Description
On Edge Transport servers, IP Block list providers are used by the Connection Filtering agent. The Connection Filtering agent acts on the IP address of the incoming SMTP connection to determine what action, if any, to take on an incoming message.
On Edge Transport servers, you need to be a member of the local Administrators group to run this cmdlet.
Examples
Example 1
Set-IPBlockListProvidersConfig -InternalMailEnabled $true -BypassedRecipients kweku@contoso.comThis example configures connection filtering to use IP Block list providers on messages that come from internal connections, but bypasses filtering for email messages sent to kweku@contoso.com.
Example 2
Set-IPBlockListProvidersConfig -BypassedRecipients @{Add="chris@contoso.com","michelle@contoso.com"; Remove="laura@contoso.com","julia@contoso.com"}This example makes the following changes to the list of bypassed recipients:
- Adds the values chris@contoso.com and michelle@contoso.com
- Removes the values laura@contoso.com and julia@contoso.com
Parameters
-BypassedRecipients
The BypassedRecipients parameter specifies the email addresses of internal recipients that are exempted from filtering by IP Block list providers.
To enter multiple values and overwrite any existing entries, use the following syntax: Value1,Value2,...ValueN. If the values contain spaces or otherwise require quotation marks, use the following syntax: "Value1","Value2",..."ValueN".
To add or remove one or more values without affecting any existing entries, use the following syntax: @{Add="Value1","Value2"...; Remove="Value3","Value4"...}.
| Type: | MultiValuedProperty |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-DomainController
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
The DomainController parameter isn't supported on Edge Transport servers. An Edge Transport server uses the local instance of Active Directory Lightweight Directory Services (AD LDS) to read and write data.
| Type: | Fqdn |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-Enabled
The Enabled parameter specifies whether IP Block list providers are used for content filtering. Valid input for this parameter is $true or $false. The default value is $true. The default value is $true. By default, IP Block list providers are used for content filtering.
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-ExternalMailEnabled
The ExternalMailEnabled parameter specifies whether messages from connections outside of the Exchange organization are evaluated by IP Block list providers. Valid input for this parameter is $true or $false. The default value is $true. By default, messages from external connections are evaluated by IP Bock list providers.
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-InternalMailEnabled
The InternalMailEnabled parameter specifies whether messages from connections inside the Exchange organization are evaluated by IP Block list providers. Valid input for this parameter is $true or $false. The default value is $false. By default, messages from internal connections are not evaluated by IP Block list providers. Authenticated partner messages aren't considered internal mail.
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-WhatIf
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.