Muokkaa

Jaa

Configure SIP Gateway

  • Artikkeli
  • Koskee seuraavia::
    Microsoft Teams

This article explains how to configure SIP Gateway so that your organization can use compatible SIP devices with Microsoft Teams. To find out what SIP Gateway can do for your organization and what hardware, software, and licenses your organization needs for it, read Plan for SIP Gateway.

Before you can configure SIP Gateway, do the following:

  • Reset SIP devices to factory default settings. You or your organization's users must reset each SIP device used with SIP Gateway to its factory default settings. To find out how to do that, see the manufacturer’s instructions.

  • Open your firewall to Microsoft 365 and Teams. Open your network's firewall to Microsoft 365 and Teams traffic as described in Office 365 URLs and IP address ranges. Firewall rules are needed for outbound traffic only.

  • Make sure the SIP devices are not behind a proxy. Ensure that http/s traffic bypasses any corporate http/s proxy.

  • Open the UDP port. Open UDP port in the range 49152 to 53247 for IP ranges 52.112.0.0/14 and 52.122.0.0/15.

  • Open the TCP port. Open TCP port 5061 for IP ranges 52.112.0.0/14 and 52.122.0.0/15.

The following sections describe what you must do as an administrator to configure SIP Gateway.

This article also describes how to:

Verify that SIP Gateway is available for your organization

  1. Sign in to the Teams admin center.

  2. At the left, select Teams devices and see if the SIP devices tab is visible. If it is, the SIP Gateway service is enabled for your organization.

Enable SIP Gateway for the users in your organization

You can enable SIP Gateway for your organization in either of two ways: by using the Teams admin center, or by using a PowerShell cmdlet.

By using Teams admin center

To enable SIP Gateway in the Teams admin center, follow these steps:

  1. Go to the Teams admin center

  2. At the left, under Voice, select Calling policies.

  3. At the right under Manage policies, select the appropriate calling policy assigned to users or, if necessary, create a new calling policy and assign it to the required users.

  4. Select Manage policies, select a policy, and then select Edit.

  5. Turn on the setting for SIP devices can be used for calls, and then select Save.

By using PowerShell

You can also enable SIP Gateway by using the PowerShell Set-CsTeamsCallingPolicy cmdlet. To enable users for SIP devices, select a policy, and set the -AllowSIPDevicesCalling attribute to True. The default value is False, so users will not be able to use their SIP devices unless you enable them.

Note

Policy propagation may take up to 24 hours.

Set the SIP Gateway provisioning server URL

You can set the SIP Gateway provisioning server's URL in your Dynamic Host Configuration Protocol (DHCP) server. Users who work remotely must configure it manually.

Using DHCP

For each SIP device, set one of the following SIP Gateway provisioning server URLs:

  • EMEA: http://emea.ipp.sdg.teams.microsoft.com
  • Americas: http://noam.ipp.sdg.teams.microsoft.com
  • APAC: http://apac.ipp.sdg.teams.microsoft.com

Add SIP devices to your Teams organization by configuring the above SIP Gateway provisioning server URL in your DHCP server. To learn more about DHCP server, see Deploy and manage DHCP. Also, you can use DHCP option 42 to specify the Network Time Protocol (NTP) server, and DHCP option 2 to specify the offset from Coordinated Universal Time (UTC) in seconds. The devices in your organization will be routed to the SIP Gateway provisioning server. Successfully provisioned SIP phones will display the Teams logo and a soft button for sign-in.

Ensure SIP devices are on the minimum supported firmware version for onboarding. During onboarding, SIP Gateway will push the default configuration and authentication user interface to the device. To find out the required firmware version for SIP devices, see Plan for SIP Gateway.

Manually

Users who work remotely must manually configure the provisioning server URL into their SIP device by using the following steps:

  1. Open Settings on the device and get the device's IP address.

  2. Open a browser window, enter the device’s IP address, log in (if necessary) and configure the provisioning server’s URL in the device's web utility.

  3. Under Settings or Advanced settings on the web utility, enter the provisioning server URL shown above.

Note

  • Only compatible SIP devices can be onboarded to SIP Gateway.
  • Cisco IP phones must be flashed to multiplatform firmware before they can be onboarded. To learn how, see Cisco firmware conversion guide.
  • For Yealink and Alcatel-Lucent Enterprise phones, use option 66.
  • For Cisco, Poly, and AudioCode phones, use option 160.
  • For Cisco devices, append /$PSN.xml to the provisioning server URL.

Configure conditional access

Conditional Access is a Microsoft Entra feature that helps ensure that devices that access your Microsoft 365 resources are properly managed and secure. SIP devices are not managed by Intune hence stricter conditional access checks are applied to them. SIP Gateway authenticates SIP devices with Microsoft Entra ID, so if your organization uses Conditional Access for devices in the corporate network, you should do one of the following:

  1. Exclude your site public IP addresses and the following SIP Gateway service IP addresses from Conditional Access checks:

    • North America:
      • East US: 52.170.38.140
      • West US: 40.112.144.212
    • EMEA region:
      • North EU: 40.112.71.149
      • West EU: 40.113.112.67
    • APAC region:
      • Australia East: 20.92.120.71
      • Australia Southeast: 13.73.115.90

  2. Exclude the Teams app from Conditional Access checks.

For more information, see IP address ranges.

Provision and enroll SIP devices as common area phones

Note

A SIP device must be onboarded to SIP Gateway before it can be enrolled.

To streamline your tasks, you can enroll SIP devices in the Teams admin center either one at a time or in batches. Here's how:

  1. Log in to the Teams admin center.

  2. Select Teams devices > SIP devices.

  3. At the upper right, select Actions > Provision devices and follow one of these steps:

    • To provision one device:

      1. Under Waiting on activation, select Add.

      2. On the Add MAC addresses pane, enter the MAC address and Location of the device, and then select Apply.

      3. Under Waiting on activation, select the device you just added, and then select Generate verification code.

      4. On the Provision devices pane, under Verification code, note the verification code for the SIP device.

    • To provision many devices:

      1. Under Waiting on activation, at the right, select Export (the Microsoft Excel icon).

      2. On the Provision devices pane, under Upload multiple MAC addresses, select download a template.

      3. Save Template_Provisioning.csv to your computer and fill in the MAC id and Location fields.

      4. On the Provision devices pane, select Upload multiple MAC addresses.

      5. At the right on the Upload MAC addresses pane, select Select a file, and select the Template_Provisioning.csv file that contains your data.

      6. On the Provision devices pane, under Waiting on activation, select a device and then select Generate verification code to generate a one-time verification code for each provisioned device. Note the verification code for each SIP device.

  4. On the SIP device, dial the enrollment feature code followed by the verification code. On the SIP device, dial the enrollment feature code *55* (used by SIP Gateway for enrollment one-time-verification code validation), followed by the verification code that is generated in Teams Admin Center for this particular device. For example, if the verification code is 123456, dial *55*123456 to enroll the device.

  5. On the Provision devices pane, under Waiting for sign in, select Signed out.

  6. In the Sign in a user dialog, the authentication URL and pairing code will be displayed.

  7. Navigate to the authentication URL on the user's desktop or mobile browser and use corporate credentials to log in.

  8. Enter the pairing code displayed in the Sign in a user dialog into the web authentication app to pair the SIP phone with the user's account. On a successful sign-in, which might take a while, the SIP phone will display the phone number and username, if the device supports it.

How to sign in and sign out

Only local sign-in is supported for users’ personal devices. To sign out a device from the Admin center, follow these steps:

  1. Log in to the Teams admin center.

  2. Select Teams devices > SIP devices.

  3. At the right, select a SIP device, and then select Sign out.

Zero Touch Common Area Phone sign in

You can remotely sign in common area phones to SIP Gateway without any physical intervention on the device.

  1. Ensure that bulk sign in pre-requisites are in place.

  2. Open the SIP remote login portal in a browser tab.

  3. Authenticate with common area phone credentials that you want to associate with the device.

  4. Select appropriate device region. You can use NOAM, EMEA, or APAC.

  5. Enter the MAC address of device in XX-XX-XX-XX-XX-XX format.

User pairing and sign-in

To pair a SIP device after the user authenticates using corporate credentials, a user must:

  1. Press Sign-in on the SIP phone to display the authentication URL and pairing code. The pairing code is time-sensitive. If it expires, the user must press Back on the phone and start the sign-in process again.

  2. Navigate to the authentication URL on the user's desktop or mobile browser and use corporate credentials to log in.

  3. Enter the pairing code displayed on the SIP phone into the web authentication app to pair the SIP phone with the user's account. On a successful sign-in, which might take a while, the SIP phone will display the phone number and username, if the device supports it.

Note

The location of the device shown on the Microsoft Entra web authentication app is the SIP Gateway datacenter to which the device is connected. SIP phones in scope are not OAuth-capable, so SIP Gateway authenticates the user through the web authentication app and then pairs the device with the user’s credentials. Learn more here: Microsoft identity platform and the OAuth 2.0 device authorization grant flow.

Note

We are introducing a new authentication experience progressively for SIP Gateway compatible devices. Users with the new experience will see a new authentication URL.

Sign-out

To sign out, a device user can:

  • Press Sign-Out on the SIP device and follow the steps described on the device.

To sign out a device on the Teams admin center:

  1. Log in to the Teams admin center.

  2. Select Teams devices > SIP devices.

  3. At the right, in the SIP devices pane, select the device.

  4. On the device's Details pane, select the Details tab, and at the upper right on the Actions menu, select Sign out.

Bulk sign in

Bulk sign ins enable you to sign in with shared accounts on SIP devices in batches of up to 100 devices each but with a limit of 3 concurrent batches per region.

Bulk sign-in is very helpful and can be used in these scenarios.

  • Activating new SIP devices When you want to activate and deploy new SIP devices within 3 days (or 72 hours) of onboarding to SIP gateway.
  • Devices that are signed out To sign in devices that got signed out for any reason, within 7 days (or 168 hours) of being signed out. In this scenario, you don't have to add the tenant ID to the provisioning URL as in Step 2 below.

Bulk sign in prerequisites

  1. You must add your site public IP address or ranges to the trusted IPs for the tenant in Teams admin center at least 24 hours prior to running the bulk sign in cmdlets.

  2. You must add your organization's tenant ID to the provisioning URL for the devices.

    Note

    The examples below are for the North America region.

    • For Alcatel-Lucent Enterprise, AudioCodes, and Yealink IP phones use: http://noam.ipp.sdg.teams.microsoft.com/tenantid/<your-tenant-ID-guid>
    • For Cisco IP phones use: http://noam.ipp.sdg.teams.microsoft.com/tenantid/<your-tenant-ID-guid>/$PSN.xml
    • For analog devices that connect to AudioCodes ATAs use: http://noam.ipp.sdg.teams.microsoft.com/tenantid/<your-tenant-ID-guid>/mac.ini

    Important

    For Cisco ATA replace mac.ini with mac.cfg. For Poly ATA replace mac.ini with $mac.cfg.

  3. You must install Microsoft Teams Power Shell 5.6.0 or later.

    Note

    The bulk sign in cmdlets aren't included with previous versions.

  4. You must apply CommonAreaPhone policy to the accounts that are part of a bulk sign in request.

  5. The accounts must not have Multi Factor Authentication (MFA) enabled.

  6. The accounts must have a phone number assigned.

  7. The accounts must have the SIP device calling policy assigned. AllowSIPDevicesCalling policy

  8. You must use an account that has the Global Administrator, Privileged Authentication Administrator or the Authentication Administrator role to run the cmdlets.

    Important

    Microsoft recommends that you use roles with the fewest permissions. Using lower permissioned accounts helps improve security for your organization. Global Administrator is a highly privileged role that should be limited to emergency scenarios when you can't use an existing role.

  9. The BulkSignIn attribute must be set to Enabled in TeamsSipDevicesConfiguration

    Note

    As a best practice, try running bulk sign in cmdlet at least 1 hour and at most 70 hours after device provisioning.

How to create a bulk sign in request

  1. Create a CSV file that will be used with two columns: Username and HardwareId.

    • Username column: Put in the list of Microsoft Entra user names or user principal names (UPNs) to use to associate with the device's MAC address found in the HardwareId column.

    • HardwareId column: List the MAC address for each IP phone in this format: xx-xx-xx-xx-xx-xx or xx-xx-xx-xx-xx-xx:xxx (where the last three digits are the ATA port number. For analog devices, the port numbers start from 001.) An example for a MAC address without the ATA port number would be: 1A-2B-3C-D4-E5-F6. An example for a MAC address for an analog device would be: 1A-2B-3C-D4-E5-F6:001

    • Example CSV:

      Username HardwareId
      FirstFloorLobbyPhone1@contoso.com 1A-2B-3C-D4-E5-F6
      SecondFloorLobbyPhone2@contoso.com 2A-3B-4C-5D-6E-7F

  2. Set up the PowerShell environment, as described in Deploy frontline static teams at scale with PowerShell for frontline workers, and get Microsoft Teams PowerShell module 5.6.0.

  3. Run the following:

    Import-Module MicrosoftTeams
$credential = Get-Credential   // Enter your admin’s email and password 
Connect-MicrosoftTeams –Credential $credential
$newBatchResponse = New-CsSdgBulkSignInRequest  -DeviceDetailsFilePath  .\Example.csv  -Region APAC

    The DeviceDetailsFilePath parameter specifies the location of the CSV you created and saved. The Region parameter specifies the SIP gateway provisioning region where the devices are being deployed. The values are: APAC, EMEA, NOAM.

  4. To check the status of a bulk sign-in batch, run the following:

    $newBatchResponse = New-CsSdgBulkSignInRequest  -DeviceDetailsFilePath  .\Example.csv  -Region APAC
$newBatchResponse.BatchId
$getBatchStatusResponse = Get-CsSdgBulkSignInRequestStatus -Batchid $newBatchResponse.BatchId
$getBatchStatusResponse | ft
$getBatchStatusResponse.BatchItem

Bulk sign in error messages

To help you troubleshoot and fix common issues, these are common error messages that you might see and what you should do to fix it.

Error message Potential solution
User not found in tenant. Check the username or User Principal Name (UPN) is correct.
User missing phone number assignment. Verify the user has a phone number assigned.
User missing AllowSIPDevicesCalling policy assignment Verify that AllowSIPDevicesCalling policy is set to Enabled. See prerequisite 7.
User missing CAP policy assignment. Verify that the account has CommonAreaPhone policy assigned. See prerequisite 4
Device not found in records. Check if the device was correctly provisioned to SIP Gateway, and the region parameter in bulk sign in request is correct.
BulkSignIn Tag missing for the device Check to see if the device provisioning URL has the correct tenant ID.
Device is offline. The device can't be found because it's powered off or disconnected from network. Reconnect the device and try it again.
Public IP not configured as Trusted IP. The tenant ID listed in the provisioning URL isn't correct or the public IP address of the device isn't listed as a trusted IP address in Teams admin center. See prerequisite 1.
Bulk Sign-in deadline expired. The device hasn't been signed in to within 72 hours of provisioning (or 168 hours).
Duplicate devices found for bulk sign-in. Verify the MAC addresses you included in the CSV file are correct and there aren't duplicated addresses. IP addresses of the duplicate devices are returned.
Input hardware-ID is of wrong format Verify the hardware-ID format. See How to create a bulk sign in request.
On-premises AD configuration failure. Contact your on-premises Active Directory team.
On-premises AD throttling detected Try it again but with a smaller number of devices in the batch. Depending on network connectivity, large batches will take more time to complete and may get stuck.
The Password writeback service failed to set a password on the tenant's local directory. The user account that is used for the device must not have User must change password at next login or User's password can't be changed selected, OR have the minimum password age must set to a value more than 0. Verify the password options aren't selected and the minimum password age is set to 0 and try again.

View and monitor SIP devices

You can view and monitor your SIP device inventory in the Teams admin center after the devices' users sign in at least once. Here's how:

  1. Log in to the Teams admin center.

  2. Select Teams devices > SIP devices. All signed in SIP devices are listed on the right.

Restart a SIP device

  1. Log in to the Teams admin center.

  2. Select Teams devices > SIP devices.

  3. On the right, select the SIP device that you want to restart, and then select Restart.

Note

  • Removing a SIP device from your tenant is currently unavailable in the Teams admin center.
  • Command execution depends on device availability, and it may not match the execution status shown in the Teams admin center. If you try to enable SIP gateway on a device that doesn't support it, the command won't be executed.

Sync policy changes to SIP devices to enforce policies

User details and policies will be fetched to SIP devices when users sign in. Any policy changes thereafter for signed-in users will be synced to the device within one hour. Devices must have their registration refreshed with the SIP Gateway periodically. SIP phones depend on Call Redirect, so the admin must set the AllowCallRedirect attribute in Set-CsTeamsCallingPolicy to Enabled.

Set a SIP device's UI language

A SIP device can usually display information in many languages. Setting its UI language affects its interface, including softkeys and sign-in/sign-out system messages. Setting the UI language is done in the provisioning server, using DHCP server, or manually by appending a code string in the URL as in the following examples.

How to set German for Polycom, AudioCodes, Alcatel-Lucent Enterprise, and Yealink phones:

  • http://emea.ipp.sdg.teams.microsoft.com/lang_de

How to set Japanese for Cisco phones:

  • http://emea.ipp.sdg.teams.microsoft.com/lang_ja/$PSN.xml

Supported languages

Language name Language code
English (default) en
Spanish es
Japanese ja
German de
French fr
Portuguese pt

Note

Japanese is not supported by Yealink and partially supported by Polycom VVX.

  • The system defaults to English if the selected language is not supported by the SIP endpoint.

  • When the lang_xx parameter is not set via the provisioning URL, English is used as the default language.

  • If Sign in to make an emergency call text is not translated to other languages, an abbreviated version in English only will be presented on Press Sign In on the following IP phone models due to a screensize limitations:

    • Poly VVX 150, VVX 201
    • Cisco CP-6821, CP-7811, CP-7821, CP-7841, CP-7861

  • Voice mail softkey label is hardcoded with VM text across all languages for Poly VVX because of a limitation of string length.

Microsoft Teams and IPv6

SIP Gateway only supports IPv4. Microsoft Teams service and client support both IPv4 and IPv6. If you want to control communications to Microsoft Teams, use the IP address ranges in Microsoft 365 URLs and IP address ranges.

Emergency calling

SIP Gateway supports dynamic emergency calling (dynamic E911) for compatible SIP devices that share network attributes over the wire. These attributes are provisioned in the Teams admin center and can be a combination of local IP and subnet length, or chassis ID and network port number. For devices that do not share location attributes, or if the location is not resolved dynamically for any reason, SIP Gateway will continue to support emergency calling based on registered addresses. Currently, registered addresses are not supported for Direct Routing scenarios. For more information about emergency calling, see Plan and manage emergency calling.

Note

Compatible Cisco SIP IP phones only support dynamic location discovery over LLDP.

Report problems to Microsoft

To report problems, contact Microsoft Support.