SPI tests in MITT

Article
01/12/2024

SPI test modules that are included in the MITT software package can be used to test data transfers for a SPI controller on the system under test and its driver. The MITT board acts as a client device connected to the SPI bus.

Before you begin

Get a MITT board and a SPI or UART adapter board. See Buy hardware for using MITT.
Download the MITT software package. Install it on the system under test.
Install MITT firmware on the MITT board. See Get started with MITT.

Hardware setup

spi mitt test.

Bus interface	Pin-out	ACPI and schematics	Connection solution
SPI	All lines needed (SCLK, MISO, MOSI, SS, GND)	ACPI table	Simple block header (on debug board)

Connect the SPI adapter to JC1 on the MITT board.
Use the jumper on the SPI adapter board to select the correct SPI voltage. The jumper can be used to select between 3.3V and 1.8V.
Connect SCLK, MOSI, MISO, SS, and GND to the system under test.
On the MITT board, set switch SW1 to the high position. This position enables the default mode for SPI when the MITT is powered. You can directly connect the board (without the SPI adapter board) if the signal is at 3.3V.

Test driver and ACPI configuration

Perform these steps on the system under test that has the I²C controller:

Install WITTTest driver included in the MITT software package by running this command:

pnputil -a witttest.inf

Note

PnpUtil.exe is included in %SystemRoot%\System32.

Modify the system ACPI and include this ASL table. You can use the Microsoft ASL compiler.

Note

Change "\\_SB_.SPI1" to ACPI entry name for the SPI controller to test as shown here. It defines three test targets with SPI frequency at 1Mhz, 5Mhz, and 20Mhz.

Device(TP1) {
    Name (_HID, "SPT0001")
    Name (_CID, "WITTTest")
    Method(_CRS, 0x0, NotSerialized)
    {
      Name (RBUF, ResourceTemplate ()
      {
          SpiSerialBus (0x0000, PolarityLow, FourWireMode, 0x08,ControllerInitiated, 0x000F4240, ClockPolarityLow,ClockPhaseFirst, "\\_SB.SPI1", 0x00, ResourceConsumer, , )
      })
      Return(RBUF)
    }
}
Device(TP2) {
    Name (_HID, "SPT0002")
    Name (_CID, "WITTTest")
    Method(_CRS, 0x0, NotSerialized)
    {
      Name (RBUF, ResourceTemplate ()
      {
          SpiSerialBus (0x0000, PolarityLow, FourWireMode, 0x08,ControllerInitiated, 0x004c4b40, ClockPolarityLow,ClockPhaseFirst, "\\_SB.SPI1", 0x00, ResourceConsumer, , )
      })
      Return(RBUF)
    }
}
Device(TP3) {
    Name (_HID, "SPT0003")
    Name (_CID, "WITTTest")
    Method(_CRS, 0x0, NotSerialized)
    {
      Name (RBUF, ResourceTemplate ()
      {
          SpiSerialBus (0x0000, PolarityLow, FourWireMode, 0x08,ControllerInitiated, 0x01312d00, ClockPolarityLow,ClockPhaseFirst, "\\_SB.SPI1", 0x00, ResourceConsumer, , )
      })
      Return(RBUF)
    }
}

SPI automation tests

Create a folder on the system under test.
Copy the TAEF binaries to the folder and then add it to your PATH environment variable. The required TAEF binaries are in %ProgramFiles(x86)%\Windows Kits\8.1\Testing\Runtimes\TAEF .
Copy Muttutil.dll and Mittspitest.dll from the MITT software package to the folder.
View all MITT SPI tests by using the /list option:

You are now ready to run SPI tests. You can run a single test, all tests at once, or run tests manually.

Run a single test by using the /name:<test name> option. This command runs the BasicIORead test:
Run all tests by using this command:
Run tests manually by using SPBCmd.exe tool included in the MITT software package.

SPI adapter schematic

spi schematic.

Share via