WDI_TLV_INTERFACE_CAPABILITIES
WDI_TLV_INTERFACE_CAPABILITIES is a TLV that contains the capabilities of the Wi-Fi interface.
TLV Type
0xF
Length
The sum (in bytes) of the sizes of all contained elements.
Values
| Type | Description |
|---|---|
| UINT32 | The maximum transfer unit (MTU) size. |
| UINT32 | The multicast list size for the adapter. |
| UINT16 | The backfill size in bytes. This value cannot be greater than 256 bytes. |
| WDI_MAC_ADDRESS | The permanent MAC address for the adapter. If the device supports multiple permanent MAC addresses, the first MAC address that will be used by the device should be returned. |
| UINT32 | The maximum supported send rate for this adapter in kbps. |
| UINT32 | The maximum supported receive rate for this adapter in kbps. |
| UINT8 | Specifies whether the radio is enabled by hardware. Valid values are 0 (disabled) and 1 (enabled). |
| UINT8 | Specifies whether they radio is enabled by software. Valid values are 0 (disabled) and 1 (enabled). |
| UINT8 | Specifies whether the interface supports PLR. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies whether the interface supports FLR. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies whether sending and receiving action frames is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | The supported number of RX spatial streams. |
| UINT8 | The supported number of TX spatial streams. |
| UINT8 | The number of channels that the adapter can work in concurrently, regardless of operation mode. |
| UINT8 | Specifies whether antenna diversity is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies whether eCSA is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies whether the adapter supports MAC address randomization. Valid values are 0 (not supported) and 1 (supported). |
| WDI_MAC_ADDRESS | A bit mask that specifies for each address bit whether it can be randomized (0) or should keep the same value as the permanent address (1). The default is all zeros. |
| WDI_BLUETOOTH_COEXISTENCE_SUPPORT (UINT32) | The supported level of Wi-Fi - Bluetooth coexistence. |
| UINT8 | Specifies non-WDI OID support. Valid values are:
These OIDs will not contain WDI headers. To identify the adapter's port that the request came in on, use NdisPortNumber in the NDIS_OID_REQUEST and match it to the one in WDI_TASK_CREATE_PORT. |
| UINT8 | Specifies whether the Fast Transition is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies whether Mu-MIMO is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies if the interface cannot support Miracast Sink. Valid values are 0 (supported) and 1 (not supported). |
| UINT8 | Specifies if 802.11v BSS transition is supported. Valid values are 0 (not supported) and 1 (supported). |
| UINT8 | Specifies if the device supports IP docking capability. Valid values are 0 (not supported) and 1 (supported). Added in Windows 10, version 1607, WDI version 1.0.21. |
| UINT8 | Specifies if the device supports SAE authentication. Valid values are 0 (not supported) and 1 (supported). Added in Windows 10, version 1903, WDI version 1.1.8. |
| UINT8 | Specifies if the device supports Multiband Operation (MBO). Valid values are 0 (not supported) and 1 (supported). Added in Windows 10, version 1903, WDI version 1.1.8. |
| UINT8 | Specifies if the adapter implements beacon report measurements. Valid values are 0 (the adapter does not implement beacon report measurements) and 1 (the adapter implements its own 11k beacon report). Added in Windows 10, version 1903, WDI version 1.1.8. |
Requirements
Minimum supported client |
Windows 10 |
Minimum supported server |
Windows Server 2016 |
Header |
Wditypes.hpp |