dot11wificxtypes.h header
This header is used by network. For more information, see:
dot11wificxtypes.h contains the following programming interfaces:
Structures
| WDI_BAND_CHANNEL_MAPPING_ENTRY Microsoft reserves the WDI_BAND_CHANNEL_MAPPING_ENTRY structure for internal use only. Don't use this structure in your code. |
| WDI_BYTE16 Microsoft reserves the WDI_BYTE16 structure for internal use only. Don't use this structure in your code. |
| WDI_BYTE4 Microsoft reserves the WDI_BYTE4 structure for internal use only. Don't use this structure in your code. |
| WDI_CHANNEL_MAPPING_ENTRY The WDI_CHANNEL_MAPPING_ENTRY struct defines a channel mapping entry. |
| WDI_DATA_RATE_ENTRY The WDI_DATA_RATE_ENTRY struct defines a data rate entry. |
| WDI_ETHERTYPE_ENCAPSULATION_ENTRY The WDI_ETHERTYPE_ENCAPSULATION_ENTRY struct defines an EtherType encapsulation entry. |
| WDI_TYPE_MIC The WDI_TYPE_MIC struct defines the MIC (802.11r). |
| WDI_TYPE_NONCE The WDI_TYPE_NONCE struct defines the SNonce or ANonce (802.11r). |
| WDI_TYPE_PMK_NAME The WDI_TYPE_PMK_NAME struct defines the PMKR0Name or PMKR1Name (802.11r). |
Enumerations
| WDI_ACTION_FRAME_CATEGORY The WDI_ACTION_FRAME_CATEGORY enumeration defines action frame categories. |
| WDI_ANQP_QUERY_STATUS Microsoft reserves the WDI_ANQP_QUERY_STATUS enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_ASSOC_STATUS The WDI_ASSOC_STATUS enum defines association status values. |
| WDI_AUTH_ALGORITHM The WDI_AUTH_ALGORITHM enumeration defines authentication algorithm values. |
| WDI_BAND_ID The WDI_BAND_ID enumeration is a UINT32 value that defines a band ID. |
| WDI_BLUETOOTH_COEXISTENCE_SUPPORT The WDI_BLUETOOTH_COEXISTENCE_SUPPORT enum defines Bluetooth coexistence support values. |
| WDI_BSS_SELECTION_FLAGS The WDI_BSS_SELECTION_FLAGS enum defines flags for BSS selection. |
| WDI_BSS_TRANSITION_RESPONSE_RESULT Microsoft reserves the WDI_BSS_TRANSITION_RESPONSE_RESULT enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_CAN_SUSTAIN_AP_REASON The WDI_CAN_SUSTAIN_AP_REASON enum defines the reasons the port is ready to receive a OID_WDI_TASK_START_AP request. |
| WDI_CIPHER_ALGORITHM The WDI_CIPHER_ALGORITHM enum defines the cipher algorithm values. |
| WDI_CIPHER_KEY_DIRECTION The WDI_CIPHER_KEY_DIRECTION enum defines the traffic directions decrypted by a cipher key. |
| WDI_CIPHER_KEY_TYPE The WDI_CIPHER_KEY_TYPE enum defines the cipher key types. |
| WDI_CONNECTION_QUALITY_HINT The WDI_CONNECTION_QUALITY_HINT enum defines the Wi-Fi connection quality hints. |
| WDI_DATA_RATE_FLAGS The WDI_DATA_RATE_FLAGS enum defines the data rate flags. |
| WDI_DISABLE_DATA_PATH_OFFLOADS_SCENARIO The WDI_DISABLE_DATA_PATH_OFFLOADS_SCENARIO enumeration is used to instruct the OS to disable datapath offloads for this connection only. |
| WDI_DS_INFO The WDI_DS_INFO enum defines values that specify whether the port is connected to the same DS that it was previously associated to. |
| WDI_ENCAPSULATION_TYPE Microsoft reserves the WDI_ENCAPSULATION_TYPE enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_EXEMPTION_PACKET_TYPE The WDI_EXEMPTION_PACKET_TYPE enum defines the types of packet exemptions. |
| WDI_FIPS_MODE Microsoft reserves the WDI_FIPS_MODE enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_FTM_BANDWIDTH The WDI_FTM_BANDWIDTH enum defines the negotiated bandwidth between two STAs to exercise the FTM. |
| WDI_FTM_PROPAGATION The WDI_FTM_PROPAGATION enum defines the propagation properties of a signal tat are estimated by the LE's logic. |
| WDI_FTM_RESPONSE_STATUS The WDI_FTM_RESPONSE_STATUS enum defines the response status for a Fine Timing Measurement (FTM) request. |
| WDI_IHV_TASK_PRIORITY The WDI_IHV_TASK_PRIORITY enum defines IHV task priorities. |
| WDI_LCI_REPORT_STATUS The WDI_LCI_REPORT_STATUS enum defines the response status for an LCI report, if the report were requested in a Fine Timing Measurement (FTM) request. |
| WDI_OS_POWER_MANAGEMENT_FLAGS Microsoft reserves the WDI_OS_POWER_MANAGEMENT_FLAGS enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_P2P_ACTION_FRAME_TYPE The WDI_P2P_ACTION_FRAME_TYPE enum defines the Wi-Fi Direct action frame types. |
| WDI_P2P_CHANNEL_INDICATE_REASON The WDI_P2P_CHANNEL_INDICATE_REASON enum defines Wi-Fi Direct channel indication reason values. |
| WDI_P2P_DISCOVER_TYPE The WDI_P2P_DISCOVER_TYPE enum defines the Wi-Fi Direct discovery types. |
| WDI_P2P_GO_INTERNAL_RESET_POLICY The WDI_P2P_GO_INTERNAL_RESET_POLICY enum defines the Wi-Fi Direct Group Owner internal reset policies. |
| WDI_P2P_LISTEN_STATE The WDI_P2P_LISTEN_STATE enum defines the Wi-Fi Direct listen states. |
| WDI_P2P_SCAN_TYPE The WDI_P2P_SCAN_TYPE enum defines the Wi-Fi Direct scan types. |
| WDI_P2P_SERVICE_DISCOVERY_TYPE The WDI_P2P_SERVICE_DISCOVERY_TYPE enum defines the types of service discovery. |
| WDI_PACKET_FILTER_TYPE Microsoft reserves the WDI_PACKET_FILTER_TYPE enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_PHY_TYPE The WDI_PHY_TYPE enumeration defines PHY types. |
| WDI_POWER_MODE_REASON_CODE The WDI_POWER_MODE_REASON_CODE enum defines the reasons for entering the Power Save state. |
| WDI_POWER_SAVE_LEVEL The WDI_POWER_SAVE_LEVEL enum defines the power save levels. |
| WDI_QOS_ACTION The WDI_QOS_ACTION enumeration defines the QOS actions. |
| WDI_QOS_PROTOCOL Microsoft reserves the WDI_QOS_PROTOCOL enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_RADIO_MEASUREMENT_ACTION The WDI_RADIO_MEASUREMENT_ACTION enumeration defines the radio measurement actions. |
| WDI_ROAM_TRIGGER The WDI_ROAM_TRIGGER enum defines roam triggers. |
| WDI_ROBUST_AV_STREAMING_ACTION The WDI_ROBUST_AV_STREAMING_ACTION enumeration defines the robust AV streaming actions. |
| WDI_SAE_INDICATION_TYPE The WDI_SAE_INDICATION_TYPE enum defines the type of information needed to continue SAE authentication with the BSSID, or notification that authentication cannot continue. |
| WDI_SAE_REQUEST_TYPE The WDI_SAE_REQUEST_TYPE enum defines the type of SAE request frame to send to the BSSID. |
| WDI_SAE_STATUS The WDI_SAE_STATUS enum defines SAE authentication failure error status codes. |
| WDI_SCAN_TRIGGER The WDI_SCAN_TRIGGER enum defines scan trigger values. |
| WDI_SCAN_TYPE The WDI_SCAN_TYPE enum defines scan types. |
| WDI_STOP_AP_REASON The WDI_STOP_AP_REASON enum defines the reasons an adapter cannot sustain 802.11 Access Point (AP) functionality on any of the PHYs. |
| WDI_WNM_ACTION Microsoft reserves the WDI_WNM_ACTION enumeration for internal use only. Don't use this enumeration in your code. |
| WDI_WPS_CONFIGURATION_METHOD The WDI_WPS_CONFIGURATION_METHOD enum defines WPS configuration methods. |