Azure vWan Hub routing between regions

Darren Mitchell 0

Hello,

We are having issues with Azure Routing, and we cannot get around this.

We have a DC in an identity network on our vWAN Hub on our North Europe Hub.

This is unable to communicate with our UK South DC on the same vWAN.

All other vms are in place and routing is fine for these vms.

Thanks

Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-12T14:05:35.45+00:00

Hello Darren Mitchell,

I hope everything is going well for you!

I wanted to make sure you had an opportunity to read my response to your query in terms of fixing the problem. Do not hesitate to contact us if you are still experiencing problems.

We are pleased to help you.

I value your time and look forward to hearing from you on this.

Regards,

Ganesh
Darren Mitchell 0 Reputation points

2024-09-12T14:27:44.05+00:00

Thanks for getting back to me.

so this turned out to be a firewall setting in hubs for hun to hub communication needed to be enabled.

We have have issues with a new vwan vpn gateway. We have site to site connectivity but no traffic is passing.

Firewall looks fine so not sure what else

Any ideas
Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-12T14:57:16.7166667+00:00
Hello Darren Mitchell,

Please confirm that the site-to-site link and on-premises address space are correctly configured.

Check whether the Azure parameters from both on-premises and site-to-site are the same.

Check the Tracert from on-premises to Azure IP Address to determine the exact issue.

Please let me know if you are still facing any issues.

Regards,

Ganesh
Darren Mitchell 0 Reputation points

2024-09-13T06:12:25.4+00:00

Hello ,

I have checked the 3 things you mentioned and they all check out.This is the setup of the vWAN

We have rules in the firewall to allow the traffic on the S-2-S to access the network etc.

We are at a bit of a loss at the moment.

Thanks for your your guidance so far.
Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-13T06:33:18.55+00:00
Hello Darren Mitchell,

Please Check from On-premises End Policy and parameters whether both the details are same or not.

Please let me know if you are still facing any issues.

Regards,

Ganesh
Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-13T16:32:34.5033333+00:00

Hi Darren Mitchell,

Have you followed the procedures and let me know whether you were able to acquire the solution?

Regards,

Ganesh
Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-16T18:09:55.8133333+00:00

Hello Darren Mitchell,

I hope you're doing well!

According to the original poster, the issue has been rectified and will aid the community as well, and now there appears to be another issue where you can be able to create a new thread; we will look into it.

We are pleased to assist you.

Regards,Ganesh

1 answer

Ganesh Patapati 1,670 Reputation points Microsoft Vendor

2024-09-11T12:22:35.9233333+00:00
Hi Darren Mitchell,

Good day!

Welcome to the Microsoft Q&A Platform! Thank you for asking your question here.

It sounds like you're dealing with a challenging Azure Virtual WAN (vWAN) routing issue.

Please check the Routes Propagation from the Azure portal; whether it is propagated or not, this can be seen in vhub.

If you have any further concerns, please do not hesitate to contact us. We are pleased to help you.

I'm looking forward to your response and appreciate your time on this.

Regards,

Ganesh
Please sign in to rate this answer.

0 comments No comments
Sign in to comment

Use comments to ask for clarification, additional information, or improvements to the question.

Share via

Azure vWan Hub routing between regions

1 answer

Your answer