Test-SenderId
This cmdlet is available only in on-premises Exchange.
Use the Test-SenderId cmdlet to test whether a specified IP address is the legitimate sending address for a specified SMTP address.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Test-SenderId
-IPAddress <IPAddress>
-PurportedResponsibleDomain <SmtpDomain>
[-Confirm]
[-DomainController <Fqdn>]
[-HelloDomain <String>]
[-Server <ServerIdParameter>]
[-WhatIf]
[<CommonParameters>] Description
The Test-SenderId cmdlet provides the results of a Sender ID check for the IP address and the corresponding domain name that you specify.
You need to be assigned permissions before you can run this cmdlet. Although this topic lists all parameters for the cmdlet, you may not have access to some parameters if they're not included in the permissions assigned to you. To find the permissions required to run any cmdlet or parameter in your organization, see Find the permissions required to run any Exchange cmdlet.
Examples
Example 1
Test-SenderId -IPAddress 192.168.0.1 -PurportedResponsibleDomain contoso.comThis example checks whether the IP address 192.168.0.1 is the legitimate sender address for the domain contoso.com.
Parameters
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-DomainController
The DomainController parameter specifies the domain controller that's used by this cmdlet to read data from or write data to Active Directory. You identify the domain controller by its fully qualified domain name (FQDN). For example, dc01.contoso.com.
The DomainController parameter isn't supported on Edge Transport servers. An Edge Transport server uses the local instance of Active Directory Lightweight Directory Services (AD LDS) to read and write data.
| Type: | Fqdn |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-HelloDomain
The HelloDomain parameter specifies the domain address displayed in the HELO or EHLO SMTP commands from this sender.
| Type: | String |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-IPAddress
The IPAddress parameter specifies the originating IP address of the sending server.
| Type: | IPAddress |
| Position: | Named |
| Default value: | None |
| Required: | True |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-PurportedResponsibleDomain
The PurportedResponsibleDomain parameter specifies the domain name that you want to verify with Sender ID.
| Type: | SmtpDomain |
| Position: | Named |
| Default value: | None |
| Required: | True |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-Server
The Server parameter specifies the Exchange server where you want to run this command. You can use any value that uniquely identifies the server. For example:
- Name
- FQDN
- Distinguished name (DN)
- Exchange Legacy DN
If you don't use this parameter, the command is run on the local server.
| Type: | ServerIdParameter |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | True |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
-WhatIf
The WhatIf switch simulates the actions of the command. You can use this switch to view the changes that would occur without actually applying those changes. You don't need to specify a value with this switch.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Exchange Server 2010, Exchange Server 2013, Exchange Server 2016, Exchange Server 2019 |
Inputs
Input types
To see the input types that this cmdlet accepts, see Cmdlet Input and Output Types. If the Input Type field for a cmdlet is blank, the cmdlet doesn't accept input data.
Outputs
Output types
To see the return types, which are also known as output types, that this cmdlet accepts, see Cmdlet Input and Output Types. If the Output Type field is blank, the cmdlet doesn't return data.