Set-SupervisoryReviewPolicyV2
This cmdlet is available only in Security & Compliance PowerShell. For more information, see Security & Compliance PowerShell.
Use the Set-SupervisoryReviewPolicyV2 cmdlet to modify supervisory review policies in the Microsoft Purview compliance portal.
For information about the parameter sets in the Syntax section below, see Exchange cmdlet syntax.
Syntax
Set-SupervisoryReviewPolicyV2
[-Identity] <PolicyIdParameter>
[-AddReviewers <String[]>]
[-Comment <String>]
[-Confirm]
[-Enabled <Boolean>]
[-Force]
[-PolicyRBACScopes <MultiValuedProperty>]
[-PolicyTemplate <String>]
[-RemoveReviewers <String[]>]
[-RetentionPeriodInDays <Int32>]
[-Reviewers <String[]>]
[-UserReportingWorkloads <String[]>]
[-WhatIf]
[<CommonParameters>] Description
To use this cmdlet in Security & Compliance PowerShell, you need to be assigned permissions. For more information, see Permissions in the Microsoft Purview compliance portal.
Examples
Example 1
Set-SupervisoryReviewPolicyV2 -Identity "EU Brokers" -AddReviewers chris@contoso.com,michelle@contoso.com -Comment "Updated for new EU regulations"This example adds reviewers and updates the comment for the supervisory review policy named EU Brokers.
Parameters
-AddReviewers
The AddReviewers parameter specifies the SMTP addresses of reviewers to add to the supervisory review policy. You can specify multiple email addresses separated by commas.
| Type: | String[] |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Comment
The Comment parameter specifies an optional comment. If you specify a value that contains spaces, enclose the value in quotation marks ("), for example: "This is an admin note".
| Type: | String |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Confirm
The Confirm switch specifies whether to show or hide the confirmation prompt. How this switch affects the cmdlet depends on if the cmdlet requires confirmation before proceeding.
- Destructive cmdlets (for example, Remove-* cmdlets) have a built-in pause that forces you to acknowledge the command before proceeding. For these cmdlets, you can skip the confirmation prompt by using this exact syntax:
-Confirm:$false. - Most other cmdlets (for example, New-* and Set-* cmdlets) don't have a built-in pause. For these cmdlets, specifying the Confirm switch without a value introduces a pause that forces you acknowledge the command before proceeding.
| Type: | SwitchParameter |
| Aliases: | cf |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Enabled
{{ Fill Enabled Description }}
| Type: | Boolean |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Force
The Force switch hides warning or confirmation messages. You don't need to specify a value with this switch.
You can use this switch to run tasks programmatically where prompting for administrative input is inappropriate.
| Type: | SwitchParameter |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Identity
The Identity parameter specifies the supervisory review policy that you want to modify. You can use any value that uniquely identifies the policy. For example:
- Name
- Distinguished name (DN)
- GUID
| Type: | PolicyIdParameter |
| Position: | 1 |
| Default value: | None |
| Required: | True |
| Accept pipeline input: | True |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-PolicyRBACScopes
{{ Fill PolicyRBACScopes Description }}
| Type: | MultiValuedProperty |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-PolicyTemplate
{{ Fill PolicyTemplate Description }}
| Type: | String |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-RemoveReviewers
The RemoveReviewers parameter specifies the SMTP addresses of reviewers to remove from the supervisory review policy. You can specify multiple email addresses separated by commas.
| Type: | String[] |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-RetentionPeriodInDays
The RetentionPeriodInDays parameter specifies the number of days that the messages will be retained for review.
| Type: | Int32 |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-Reviewers
The Reviewers parameter specifies the SMTP addresses of the reviewers for the supervisory review policy. You can specify multiple email addresses separated by commas.
The reviewers that you specify with this parameter replace the existing reviewers. To selectively add or remove reviewers, use the AddReviewers and RemoveReviewers parameters.
| Type: | String[] |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-UserReportingWorkloads
{{ Fill UserReportingWorkloads Description }}
| Type: | String[] |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |
-WhatIf
The WhatIf switch doesn't work in Security & Compliance PowerShell.
| Type: | SwitchParameter |
| Aliases: | wi |
| Position: | Named |
| Default value: | None |
| Required: | False |
| Accept pipeline input: | False |
| Accept wildcard characters: | False |
| Applies to: | Security & Compliance |