DrawText
A version of this page is also available for
4/8/2010
This function draws formatted text in the specified rectangle. DrawText formats the text according to the specified format method.
Syntax
int DrawText(
HDC hDC,
LPCTSTR lpString,
int nCount,
LPRECT lpRect,
UNIT uFormat
);
Parameters
- hDC
[in] Handle to the device context.
- lpString
[in] Long pointer to the string that you want to draw. If the nCount parameter is –1, you must specify a null-terminated string.
- nCount
[in] Integer that specifies the number of characters in the string. If nCount is –1, DrawText assumes that the lpString parameter is a pointer to a null-terminated string and computes the character count automatically.
- lpRect
[in] Long pointer to a RECT structure that contains the rectangle, in logical coordinates, in which you want to format the text.
uFormat
[in] Unsigned integer that specifies the method of formatting the text. The following table shows the possible values that you can combine to create a value for this parameter.Value Description DT_BOTTOM
Justifies the text to the bottom of the rectangle. You must combine this value with DT_SINGLELINE.
DT_CALCRECT
Determines the width and height of the rectangle. If the rectangle includes multiple lines of text, DrawText uses the width of the rectangle pointed to by the lpRect parameter and extends the base of the rectangle to bound the last line of text. If the rectangle includes only one line of text, DrawText modifies the right side of the rectangle so that it bounds the last character in the line. In either case, DrawText returns the height of the formatted text but does not draw the text.
Before calling DrawText, an application must set the right and bottom members of the RECT structure pointed to by lpRect. These members are updated with the call to DrawText.
DT_CENTER
Centers text horizontally in the rectangle.
DT_END_ELLIPSIS
Truncates a text string that is wider than the display rectangle and adds an ellipsis to indicate the truncation.
DT_EXPANDTABS
Expands tab characters. The default number of characters per tab is eight.
DT_INTERNAL
Uses the system font to calculate text metrics.
DT_LEFT
Aligns text to the left.
DT_NOCLIP
Draws without clipping. DrawText is somewhat faster when DT_NOCLIP is used.
DT_NOPREFIX
Turns off processing of prefix characters. Normally, DrawText interprets the mnemonic-prefix character & as a directive to underscore the character that follows, and the mnemonic-prefix characters && as a directive to print a single &. By specifying DT_NOPREFIX, this processing is turned off.
DT_RIGHT
Aligns text to the right.
DT_RTLREADING
Layout in right-to-left reading order for bi-directional text when the font selected into the hdc is a Hebrew or Arabic font. The default reading order for all text is left-to-right.
DT_SINGLELINE
Displays text on a single line only. Carriage returns and linefeeds do not break the line.
DT_TABSTOP
Sets tab stops. Bits 8–15, which form the high-order byte of the low-order word, of the uFormat parameter specify the number of characters for each tab. The default number of characters per tab is eight. You cannot use the DT_CALCRECT, DT_EXTERNALLEADING, DT_INTERNAL, DT_NOCLIP, and DT_NOPREFIX values with the DT_TABSTOP value.
DT_TOP
Top-justifies text. You must combine this value with DT_SINGLELINE.
DT_VCENTER
Centers text vertically. You must combine this value with DT_SINGLELINE.
DT_WORD_ELLIPSIS
Truncates any word that does not fit in the display rectangle and adds an ellipsis.
DT_WORDBREAK
Breaks words. DrawText automatically breaks lines between words if a word would extend past the edge of the rectangle specified by the lpRect parameter. A carriage return-linefeed sequence also breaks the line.
Return Value
The height of the text indicates success. Zero indicates failure. To get extended error information, call GetLastError.
Remarks
The DrawText function uses the selected font, text color, and background color for the device context to draw the text. Unless you specify the DT_NOCLIP value, DrawText clips the text so that it does not appear outside the specified rectangle. DrawText assumes that all formatting has multiple lines unless you specify the DT_SINGLELINE format.
If the selected font is too large for the specified rectangle, the DrawText function does not attempt to substitute a smaller font.
For Windows CE 2.10 and later, line breaking is supported for the Chinese, Korean, and Japanese languages.
Requirements
| Header | windows.h |
| Library | coredll.lib |
| Windows Embedded CE | Windows CE 1.0 and later |
| Windows Mobile | Pocket PC for Windows Mobile Version 5.0 and later, Smartphone for Windows Mobile Version 5.0 and later |